Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello All,  I state that I'm very fast Voip router configurations, the problem is as follows:  I need to configure a SPA3102 so that I hijack a line RTG via LAN / WAN or on a SPA2102 .... in the motion that the 2102 can receive and make calls ..     ...

My flash currently contains -BNE3825RT02#dir Directory of flash:/    1  -rw-    29327868  Mar 23 2006 12:33:16 +10:00  c3825-spservicesk9-mz.124-3c.bin    2  -rw-        1649  Jan 24 2006 06:06:16 +10:00  sdmconfig-38xx.cfg    3  -rw-     4052480  Ja...

cisco by Level 1
  • 2486 Views
  • 2 replies
  • 0 Helpful votes

Hi guys,I just inhereted a network which has 7 switches (3750s) as a Stack. In there, there are 5 SVI (switch virtual interfaces) and in each of these VLANs, HSRP is configured.Question:Is HSRP really needed in a Stack configuration?If so, what are t...

I have a RR advertising 380k prefixes to two RR clients.show bgp n x.x.x.x advertised on the RR shows that full 380k routes are being sent to the RR clients.One client is recieving the whole 380 while another clent is only seeing 260k routes as indic...

Hi,I'm trying to configure an ACL on a 2950, but I can't seem to make it work properly.here's my ACL,access-list 100 permit ip host 10.136.10.1 host 10.12.5.176access-list 100 deny ip any host 10.12.5.176access-list 100 permit ip any anyI assigned th...

tonyp8581 by Level 1
  • 477 Views
  • 2 replies
  • 0 Helpful votes

  Hi there I recently implemented SLA monitoring for failover of 2 ISPs. On Friday we had a major problem as some packets were getting thou and some weren't, due to problems at the ISP, so  the router was constantly switching from the main route to t...

Resolved! Multi-Protocol BGP

With IPv6 Coming i've been tasked with implimenting M-BGP on our 7200VXR running 12.4 and was wondering if someone could point me to either a good reference to configuring this or possibly shooting me an example config.Little to nothing is my experti...

ixholla69 by Level 1
  • 1307 Views
  • 5 replies
  • 0 Helpful votes

Hi, I have Cisco 2851 router & need to allocate bandwith based on IP's. eg. 192.168.1.1 should use 7 Mbps & 192.168.1.2 should use 2 Mbps & 192.168.1.3 should use 1 Mbps. Let me know the configuration on how to execute it on a router.

Hello,We just acquired our 2nd ISP. I need some advice on what's best configuration or setup to our internet connection. Our goal is to maximize first all the bandwidth of 2nd ISP then when it's full, it goes to1st ISP. Please see network diagram bel...

rgbatucan by Level 1
  • 871 Views
  • 3 replies
  • 0 Helpful votes

HI,Due to a bug int the IOS (F4 loosing routing information) i needed to upgrade the IOS from 15.0.1-M4 to the latest one which is 15.1.Is it ok to do without valid Smartnet contract? Cisco website allowed me to download the IOS and then put it on th...

Resolved! Ip Local policy

Dear All,    Can you pls help get idea on IP Local policy command  with static route with sample config.Is there any detail document is available.Regards,Ajith

I'm trying to understand the relationship between bandwidth and interface queueing. Do full queues mean 100% bandwidth or 100% bandwidth mean full queues? Always? I'm looking at a network graph that reports 15 minute averages and the traffic never go...

AJ Cruz by Level 3
  • 1001 Views
  • 4 replies
  • 0 Helpful votes