Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

How to determine bandwidth req'd over WAN...

I've searched this forum for answers and I'm sure this question has been asked a thousand times, but I'm being asked to provide hard numbers for bandwidth usage based on very little information.We are looking at a new piece of software which does not...

maxnpj by • Level 1
  • 692 Views
  • 2 replies
  • 0 Helpful votes

Router recomendation for a 100 Meg WAN?

Dear AllI really need help choosing a router to support a 100 Meg WAN. It must be able to handle the full 100 Meg throughput at an MTU size of 1440-1500. No need for modules or interface cards because I will use the onboard FE/GEs.It will just be for...

msaltissi by • Level 1
  • 14337 Views
  • 6 replies
  • 0 Helpful votes

How do I remove awkward config?

ROUTER#sh run | i ip cefip cef table event-logip cefip cef accounting non-recursive load-balance-hash ip cef accounting non-recursive external>snip<ROUTER#conf tEnter configuration commands, one per line.  End with CNTL/Z.ROUTER(config)#no ip cef acc...

moxeysp by • Level 1
  • 611 Views
  • 3 replies
  • 0 Helpful votes

Resolved! ASM SSM multicast in MPLS domain

in our mpls network we have ssm deployed for multicast, but for some old reason there is a static RP also defined on each box and as per my understanding it is not required incase of SSM. we are planning to remove the RP entry but after removing it f...

Resolved! Multiple PPP Multilinks in 7609 router

We have Cisco 7609 routers in our network. We are using ppp multilinks between the sites. Because of the high traffic volume, we have to use multiple multilinks. 7609 router doesn't allow ppp multlink to span SIPs, so we use multiple mulitilinks bet...

f-m-s-2000 by • Level 1
  • 2945 Views
  • 21 replies
  • 0 Helpful votes

Resolved! Can not dial out from ISDN Line with 1812j

Hi, Now I am tring to setup Cisco 1812j with ISDN Line.Here is what I connect the device.(I am in Japan)ISDN Line (NTT east) >> DSU(NTT east INS Mate V30Slim with S/T port) >> Cisco 1812j(S/T)On DSU setting I enable DSU and Disable Terminator.First o...

useful tool for comparing routing table.

Dear.I would like to know Is there any other useful tool for compare each routing table?because, we need to check the routing table. current backbone routing table and another routing table.Please let us know if there is tool which is to compare rout...

syjeon by • Level 1
  • 1006 Views
  • 0 replies
  • 0 Helpful votes

Resolved! ASA -> ROUTER -> LAN - syslog question

Hello, I am running the following configcloud -> ASA -> ROUTER -> LAN,I am doing NAT/PAT on the router instead of the ASA because I am bumping up against my 10 user license.Everything is working fine, but I am having an issue trying to get the asa to...

Resolved! OSPF - NSSA & Area 0

Hi All,I'm hoping the community can help me out with this one....I have a WAN connection to a site that is being brought into my network via MPLS.  The Service Provider and my edge router is using BGP.  The BGP routes are being redistributed into OSP...

jc84_ by • Level 1
  • 2209 Views
  • 13 replies
  • 0 Helpful votes

Resolved! Users supported against router modle?

Good Day Everyone,I am looking around the Cisco site for a table showing the Cisco router model number against the number of user supported.I have had a sales person ask me if an 1841 would support 20 users with the possiblility to grow to 50 and in ...

alalli by • Level 2
  • 519 Views
  • 3 replies
  • 0 Helpful votes

WAN E1 PRI CONFIGURATION ON 2811 & 1841

Dears ExpertsHiCould  you help me to Install WAN NETWORKto  PLEASEMain Office ( HQ):  Cisco  Integrated Service Router 2811 1 Port Channelized T1/E1 and ISDN  PRI High Speed WAN Interface Card E1/GSHDSL Modems Cisco 2800  IOS firmware Branches :Cisco...

Resolved! E1 maximun channel-groups

Dear all,I currently have a VWIC2-1MFT-T1/E1 card.This card does not allowed me to configure more than 2 channel-groups in my E1 port.I need to use a channelized E1 with 10 different channel-grous (10 different conections for branch offices).Ive read...

o_unzueta by • Level 1
  • 861 Views
  • 2 replies
  • 0 Helpful votes
View All
Review Cisco Networking for a $25 gift card