Hi, after router reloads (manual or power loss) the nbar statistics disappear and begin from 0.is there any setting to save historical data even after reloads? Thanks
Hi, after router reloads (manual or power loss) the nbar statistics disappear and begin from 0.is there any setting to save historical data even after reloads? Thanks
hello, I have router A9K 9006,I use it as BNG, with client POOL private ip address,I need to enable CGNAT for private ip addresses to the public, what plugin hardware requirements must add to my router, and is need a license or not? 0/RSP0/CPU0 A...
Hi, i have C1111-4P router, with Software 17.6.3a installed, Smart license status ENABLEDThere is no CLI command available license smart registerAlso the web-based konfiguration cant load Licensing menu.I want to connect to my smart account and regis...
if ISR4321 support BGP
Hello everyone, Regarding ospf summarization, please correct and advise me: area 15 range summary-address mask. this will advertise my summary address from area 15 into backbone. and is done on abr.internet------asbr(area15)-------(area15)abr(area0)...
is there any difference between the two terms? and speaking about the old 1st,2nd ISR ex (2800,2900), are the CPU and RP physically seperated ? or it is all about seperated functions where the RP is where the routing processes take place ? Thank you...
Hallo,I have an ISR1100 LTE dual-sim router. The router has two VPN tunnels configured each using the cellular interfaces as the the sources. Failover when one sim card fails works perfect. I would however like to loadbalance the traffic between thes...
I have two sites connected via a private MPLS. Site-1 has 2 PE devices and site-2 has a single PE device. I need to extend some of the vlans between the two sites. I am looking at implementing EoMPLS to accomplish this as it is two sites only and MPL...
I ahve some Guest Docker Ubuntu containers, they can connect to the topology but I want to add static routes. How can i add a static route to it? It seems like route add command might do something
I have single router connected with 2 different ISP. One link is 10G interface 1 and another link is 1G interface 2. Can I control all incoming traffic 70% via interface 1 as this is 10G link and 30% traffic incoming via interface 2 as this is 1G lin...
What does these columns mean/how do I interpret it? Column 1 'H' Column 4 'SRTT' column 5 'RTO' Thank you
I have a simple scenario as in the diagram: I am advertising a route 40.40.40.0/24 from R4 to AS 100. When I verify BGP table in the R1,R2,R3: R1#show ip bgpBGP table version is 8, local router ID is 1.1.1.1Network Next Hop Metric LocPrf Weight Pat...
Hi! I´m receiving the error Failed to commit one or more configuration items during a pseudo-atomic operation. All changes made have been reverted. Please issue 'show configuration failed [inheritance]' from this session to view the errors.I received...
Thought just occured to me as to whether or not I should be able to ping acorss this trunk portswhile doing this lab In doing a HSRP lab between the switches I recognized there needed to be communication between the switches to elect the active spea...
We have a case today of reported Internet 'slowness'. We recently encrypted links out to this location. I noticed right away that pings to 8.8.8.8 would not work at 1500 bytes. Snooping about a bit on this, I found this in the output of a command: xx...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-20-2024 04:56 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM |
User | Count |
---|---|
15 | |
12 | |
6 | |
5 | |
2 |