Routing

Resolved! MPLS-Branch to Branch connectivity

Dear All,I have Head office and Branch offices connected using MPLS VPN. It is not fully meshed, It is Hub & Spoke TopologyNow I am able communicate between branch offices and Headoffices.But I want communication between Branch offices thru Head offi...

Multilink bundle bandwidth statement

Is it enough to have your bandwidth statements on the serial interfaces, or should you double that and put it on the multilink bundle interface?Thanks,John

Resolved! ISDN PRI Voice Capable

Which of the following ISDN PRI interfaces are capable for both voice and data:NM-1CE1T1-PRIHWIC-2CE1T1-PRIVWIC2-2MFT-T1/E1It would be installed on an 2801 router.

Resolved! Confirmation of 'redistribute static' on OSPF

Hi, Imagine on RouterA I have advertised all respective networks. I do not have any static routes configured (by using ip route command).That said, is there any need to issue command "redistribute static metric <> metric-type 1 subnets"?loopback0 ip ...

Qos not applied even when Service-Policy command is entered.

Hi,I have an issue with two of our BIP links.On our HQ BIP link and on our High Availability BIP link when you enter the Service-Policy command, the command is accepted but when you do a sh run and look at the running config, you cannot see where the...

Resolved! How to backup ADSL connection over Ethernet interface

Using a Cisco 877 router with ADSL connectivity, a backup connection is needed. A 3G (cellular) device is available, capable of setting up an IPsec VPN, and offering an ethernet port for connecting the (backup) port of the 877 router.Neither the ADSL...

Resolved! OSPF Area

How many routers and users can be in a single OSPF area?

how to remoce clock rate

I have 2851 router with this IOS VERSION ((C2800NM-ADVIPSERVICESK9-M), Version 12.4(9)T1, ) and the clock rate 2000000 is on the serial interface by default,im try to remove it but it's not going,i dit no clock rate and no clock rate 2000000 on the i...

Overcoming inbound link resilience without dynamic routing

Greetings, im sure this question has been approached several times before but it would be appreciated if i could get some opinions.We have a customer with two DSL connections coming into two different routers, we want to replace these connections wit...

Resolved! Configure two routers in bridge mode

Hi, i need to configure two Cisco routers in bridge mode as they interconnect two LANs that are in the same subnet. The two routers are connected by a fiber optic link. Can you please indicate me how to set the routers in bridge mode.

interview Question asked to me ...

I need answer of the below question.1. What is FIB? what it does? where it is present? is it L3 switch, router and L2 switch.?3.What is the differnece between Pagp and LCP?4. What RPF, what is does.?5. In ISDN my call is disconnected every 2 minutes,...

INTERNET CONFIGURATION ISSUE

Hi,Please can someone help me with this.In my Access List configuration for our internet users, in order to implement the company's policy. I have one Access List that is to gives users access to the Internet (Web) in the morning and I have another A...

Calls routing out the wrong gateway.

Hi,Recently we started to route all our outgoing National call though our carriers network to get cheaper calls. Since we rolled this out we have noticed that all these calls are routing across two sites before it leaves our network.I have attached a...

changeing lease line from serial to FE

Hi all, i have upgrade the lease line and also change serial to fast ethernet port so pls suggest me that ,how can change the local crypto endpoint,remote crypto endpoint and crypto map tag and crypto ipsec . and also specific changes required ...

L3 Routing Problem

hi experts,i have a 6509 and a 3750 connected via FSO (free space optics). i will be adding a fiber connection on both swithces. both FSO and fiber have L3 IP address configured. how can i route properly, avoiding loops, between these devices? i'm co...