<p>I have an 1841 with two internet circuits and I'm wanting to configure the circuits for failover. Is there a way to have the router ping ISP1s default-gateway and if it fails use ISP2s gateway? Please note that it is imperative I track an IP add...
Just got a new CISCO881-SEC-K9 which should come with Advanced IP Services Feature set and include EIGRP, DMVPN .... (CISCO881-K9 only has Adv. Security) http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542.htmlBGP, OSPF, DM...
<p>Hello,</p><p>What is the difference between an OSPF LSA 4 and OSPF LSA 5? Both are sent from an ASBR but I am not sure what makes them different.</p><p>Thanks,</p><p>Richard</p>
Hello,I have to establish several VPN tunnels between different sites, all equipped with the above devices, the RVL is the point, there is one PC behind, that has to download and run an application. I can establish the tunnel with no errors in the lo...
Hello,Is there any downside to using redistribute connected in a full mesh BGP environment, when OSPF is used as the IGP?Reason I need to use redistribute connected is because of the few hundred VLAN interfaces I have on my 6500s, and did not want to...
<p>Hi Experts,</p><p>Looking for a little help with a QoS config. I have a customer connected to an MPLS cloud. they have two sites, and both sites have 10 Mb into the cloud.</p><p>Our Data center has a 100 Mb link into the cloud. We provide internet...
<p>Hello;</p><p>We have two 7206 VXR thats connected to one isp over two metro ethernet lines.</p><p>One of them use 30mbit the other one is 50 mbit. We use bgp in our environment to connect internet.</p><p>We configure route-maps.</p><p>For example...
Hi All, I have client with 2 ISPs/Dual routers. ISP-A :10Meg & ISP-B : T1 Local public IP space advertised to ISPA & ISPB via EBGP (with ISP-B : via AS-Prepend). LAN side of the routers has HSRP config to have ISP-A Connected router as Primary and IB...
All,<br /><br />I have a point-to-point link between two sites. This link constantly has traffic going through it (it's a DR site), and we're replicating across the link. Sometimes (a lot this week), we "lose" connection to the other side. I've repor...
Hello AllSmall confusion here.. I have two routers with identical configs of eigrp.. The idea here is to advertise a static route connected to the core routers. We are now trying to advertise the supernet of the static segment with the following comm...
<p><br />I am trying to figure out what would be the best way to provide redundant Internet access across two sites running BGP full routing tables at the edge and OSPF between the sites. My main goal is to be able to have fail-over to the other site...
I am trying to setup a VPN backup solution for one of our MPLS connected branch offices. I've configured the tunnel interfaces as required and that is working as expected, however I'm looking for suggestions on which direction to go with the routing...
can anyone guide me? I have 2801 with integrated hwic 9 poe and 79xx phones,can i bridge my (dynamic) dsl modem into router and access internet through switch port on 79xx phone? I can find no info on step by step in this or any forum.I have seen all...
<p>Hi,<br />I have 2 routers R2 and R3 in a point-to-point serial connection. OSPF is configured.<br />R2 is getting interArea routes forwarded by R3. I still don't know why R2 gets /32 prefixes these routes.<br /><br />example on R2:<br />" 192....
