Routing

Hi AllI have a 2600 series router and I'm trying to type in a lengthy MOTD. However, it stops letting me type after about the 3rd sentence. Is there a limit to the length of the MOTD? It appears so.Is there a way I can change the allowable length of ...

Dear All,Is it possible to configure InterVlan on 877 series? I tried configuring subinterfaces on Fa 1-3 and failed. Can someone please suggest.IOS Version: C870 Software (C870-ADVSECURITYK9-M), Version 12.4(4)T2.

if i have 3 routers connected and all have LANs behind them too.i issue the >show ip route command and i see couple of routes that were learned via EIGRP and couple as Directly-Connected.so when a host on the LAN sends a packet - will the router pref...

There are 2 interfaces (fa 0/0 and atm 0/0) The atm interface shows 178/255 during business hours. The highest process was .39% in 5 minutes (CEF). How do I determine whether this is traffic, old hardware, or other?

Hello - this may just be a provisioning issue with AT&T, but I want to make sure all my ducks are in a row. I have a 2691 with two ATM/T1 links going into a VWIC-2MFT-T1. They are configured in a IMA group. I have added a VWIC2-2MFT-T1 and brought...

Hi,We have just set up a VPN (well almost) between my office in the UK and our US office. We need to connect to resources on the US side from the UK. The US team have provided the equipment to do this, problem is we have a few networks our side tha...

Hi Experts,Can I know if the EIGRP will suddenly loses all of the neighbors for the updates??Any cause of this that can make this happens?Thanks in advanced.

Hello,Here is my scenario.Business with two locations.LOCATION 1:*Cisco 2811*Firebox Watchguard X700*T1*Public IP on Cisco Ser*Privite Ip 172.28.159.1 on Cisco eth0/0*X700 also has a pub ip assigned to it as well as a priv ip*X700 is where I have my ...

Hi allI am configuring "Drop and Insert" in VWIC2-2MFT-T1/E1 on router 3845.My topo follos: PBX--R3845---Wan(voice and data)---R3845---PBX.After configuring, Voice and data is OK. I can make a phone call and ping successfully. But Fax and Modem analo...

if i have this wildcard mask:0.0.0.15does it mean that the "do-care" bits are the last 15 bits? so in binary its:10000000.00000000?and how i interpret this wildcard mask:0.0.15.255?

I know I've come across this before, but can't remember solution/answer.I am unable to ping a remote server interface from our hub router unless I use extended ping.I can ping from my PC to the server, just not directly from the router (unless using ...

hi,i am hosting an application server at HO to which clients connect using the client application, using 2 ports.(8090,8092). We were using a DSL connection and eveyrthing was good.Now we bought an E1, terminated it on 2811 using e1 controler card.I ...

I have a lab setup with a router, layer three 3550 switch and a PIX firewall.The router and the firewall are plugged into the switch in seperate VLANs and are using the switch as their default gateway.All three devices are configured in the same OSPF...

Friends,I have a cisco 2610 router, IOS version 11.3(8)T1. Though i have logging configured, the router does not show any log messages and i am not sure what the problem is. Plz find below the config that i have.logging buffered 16384 debuggingloggin...