Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi.I'm configuring MQC between a 6500 and a 7304 on a Gi interface. I'm using the bandwidth command to mirror a bottleneck further on in the network and then bandwidth percent for each traffic class. Reading the documentation for bandwidth, I expecte...

When I access my PIX remotely or from the LAN it will drop the connection about 10 mins into configuring anything, even if I'm using the interface and monitoring. I then have to shut off my browser, wait a few minutes, then connect again. This is hap...

HiI have just install Cisco 4503 Switch. I want web access the switch for visible the port status. I can check port in 2950.but in 4503 when i web acess the ip i just see in text mode no visible port status. so How i can I see the visible port status...

iqbalkhan by Level 1
  • 475 Views
  • 1 replies
  • 0 Helpful votes

hiIn core switch we found port support 10/100/1000 and many port only mention 1000 based. so the port which only support 1000 based they can confirure for 100 based???thanksbiplob

iqbalkhan by Level 1
  • 456 Views
  • 2 replies
  • 0 Helpful votes

Hi,I'm trying to adjust the TX-ring limit on a vbr-nrt vc 20Mbit/s. We are using fancy queuing with RED enabled in the default class. We also run a voice class so we want to keep jitter and and delay to a minimum.When I use a TX-ring limit of 12 for ...

danne by Level 1
  • 813 Views
  • 6 replies
  • 0 Helpful votes

Hi All,i am about to buy a 5505 with the following cards installed:System rack contains:-1 x Power Supply ModuleSlot 1.WS X5530-E3A Supervisor engineWS U53534 GESX 1000 Base SX Gbit EthernetSlot 2.WS-X5225R 24 port 10/100BaseTxSlot 3.WS-X5224 24 port...

I am yet to get the crashinfo files from customer to troublehoot this VIP6-80 crash in slot 4. But I have the SHOW TECH and SHOW LOG attached. I have checked the Bug Tool Kit and there are some S/W defects that can cause this, but most of the results...

HiWhy does my router get interface resets although the line is down?Serial1 is up, line protocol is down Hardware is HD64570 Description: Internet address is MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HD...

Hi,We have recently had an MPLS link put in between to sites. One end has an 1800 series router connected to a Pix 515e the other has a 3845 Router connected again to a PIX 515e. I've used a spare interfaces on both the 515e's and added the following...

johnnymac by Level 1
  • 544 Views
  • 4 replies
  • 0 Helpful votes

Hello,Could you please help me with the following problem. I whant to conect two Inernet channels from different providers over the PIX. One of the Internet channel I whant to use as the main and another one as the redundant. So the second one will n...

bridgecom by Level 1
  • 332 Views
  • 1 replies
  • 0 Helpful votes

IOS

hi.. anybody you there knows all about the router command or IOS can you give where a good site for those command

paulgrg22 by Level 1
  • 588 Views
  • 4 replies
  • 0 Helpful votes

I have a particular 2950 12 switch that the Cisco Network Assistant shows as having a failed redundant power supply error. I pulled the switch from the rack and there is only a single power supply in it and it is functioning. Can I just acknowledge t...

neilh by Level 1
  • 2256 Views
  • 2 replies
  • 0 Helpful votes