Hello experts! i am doing DMVPN but the problem here is : NPJ-router is not getting the route for SERVER-AREA-DR loopback. hence HO-router is getting both route for LAN network from NPJ & SERVER-AREA-DR loopback. can say, NPJ & SERVER-AREA-DR are not...
Forum Posts
Resolved! IGMP Queierer "Global IP Address"?
I found many references to a router's Global IP Address in this document on multicast config, for instance: Prerequisites for IGMP Snooping Observe these guidelines when configuring the IGMP snooping querier: Configure the VLAN in global configu...
Hi all, We have RV340 as LAN firewall. I am trying to open one port, but only for 2 remote IPs (not for all the internet). I tryed with this configuration for access rules. In that way service it´s open for all the internet. Am i doing something wro...
Hi,There are eight different queue's per interface for qos on XR devices , how can i check queue's traffic statistics (total traffic flowing through each queue, buffer size, peak rate, discards etc..) on an interface. Thanks
Resolved! BGP Issue - 2 AS on same router ?...
Hi Team, I working in some company's lab that gives services to clients. We are getting the networks/subnets from IT and then distribute it in the lab as we want per client's needs. The gateways for the subnets to get out from the lab to the 'world' ...
Hello,I have a very rudimentary understanding of the Internet/networking and am looking to learn more. After looking up an IP address associated with a VPN, I noticed that the ISP associated with the IP address was different from the ASN (I have atta...
Resolved! OSPF Keychain auth issue
So I configured 2 switch interfaces to use Keychain Authentication and after the key expires the switches still propagates the OSPF Networks instead of shutting off the adjacency....any idea why this is happening? This is the config I used: enablec...
i have Existing site to site vpn configurations on cisco router and plan to migrate it to the new FortiGate firewall what method should i follow to make this happen
Resolved! Nexus 9000 IGMP join issue
Hi All, Device: cisco Nexus9000 C9348GC-FXP Chassis NXOS Version: 9.3.7 We are seeing a behavior in our IGMP joins that not all of the groups are joining at the same time. Checking the IGMP debug, I'm getting these messages for the groups that d...
Hi,I have a RV160 router that I want to use between a device that has the same ip adress as another device that i'm connected to. I want to use static NAT on this device to hide his adress and expose another one.I thought that static Nat would be eas...
I have a problem with my Nexus 5548UP.The data transfer between 2 Vlan's is very slow.Data transfer in same vlan's is ok.Have installed a L3 card and a LAN_ENTERPRISE_LICENSEInter-Vlan routing works.See pictures: Here is a PC in vlan 30 with 10Gbit S...
Hello,I have two edge routers(R-A and R-B) located in two data centers. Data center A and Data center B. internet service provider router also present at both data center( ISP-A and ISP-B). Data center A is primary location and Data center B is for b...
I have Internet only Verizon Residential FIOS. The Ethernet port is the active port (instead of the coaxial) on my Verizon Optical Network Terminal (ONT) box because I do not have TV service that uses coaxial connection. I am trying to interconnect ...
HI all, I am migrating connections from cicso 2800 router to nx-os 3458. In cisco 2800 i am using subnet to subnet nat commands, but i am unable to replicate this in nx-os 3k. The routers are performing Source + DNAT for same traffic going out. Us...
Hello. I have a rather strange problem with my FPR2110 (running on ASA appliance mode). ASA version is 9.14(3)18. I have set up routing of multicast packets to some interfaces - including bridge group interfaces. When I restore the configuration usin...
