Resolved! 2811 support NM-8E1-IMA?
Does 2811 supports NM-8E1-IMA card? I have 2621 router with this card in use and I'd like to get 2811 and put this same card in it. Is it possible?thanks!
Does 2811 supports NM-8E1-IMA card? I have 2621 router with this card in use and I'd like to get 2811 and put this same card in it. Is it possible?thanks!
i have a central site and remote site. i want to establish site to site VPN.at the central site i have got leased line with public IP.my remote site is using an ADSL connection, in this case i will not get any Public IP.on the ADSL interface i will ...
Hi, I think you might be already aware about unknown unicast flooding issue with NLB clusters. In brief, the issue is as follows... L-3 Router - L-2 switch - cluster nodes L-3 router learns only NLB cluster MAC address and whereas L-2 switch learns i...
Does enyone have expiriance with following message?*Mar 6 03:37:54.865: %SYS-2-MALLOCFAIL: Memory allocation of 64508 bytes failed from 0x606567FC, alignment 0Pool: Processor Free: 104324 Cause: Memory fragmentationAlternate Pool: None Free: 0 C...
I need advice and hope this is the right forum. I have a dedicated T1link between one branch office and our home office. I would like all traffic from all users in the branch that go to certain hosts in the home office to get higher priority than o...
Hi,here is the diagramR1--1.1.1.0/24--R2---2.2.2.0/24--PCR1 IP is 1.1.1.1/24R2 IP is 1.1.1.2/24 and 2.2.2.1/24PC IP is 2.2.2.2/24R1, R2 and PC can talk each otheron PC, I use console to configure R2(called Windows2) and in the same time, I have a tel...
how can i identify that the memory usage is high on my router. show memory processes - doesnt show the full resources and utilizations
HelloI tried to configure IPV6 RIP over FR, and i exeperienced wierd thing, I just enabled ipv6 rip and ipv6 without FR mapping, but it works fine OKed ping and OKed rouging table. it was FR main interface and no frame-relay interface-dlci xxx .... a...
Scenario:1 cisco 2801 that has 2 t1's going into it. The t1's are from seperate providers, so two differnt networks.The t1's each have an additional /30 block of addresses routed to themt1:1 network 1.1.1.0/30 has network 1.1.2.0/30 being routed to i...
Hi,How to interconnect T1 line and E1. What are the devices needed for that?.Valuable suggestions are appriciated.Thanks in Advance.
Dear Sir/Madam,My network as follows:ISA 2004-10.0.0.1----10.0.0.2-Router 1841-------------lesse lineI-----------ADSLI want all users access internet through ISA 2004, all traffic out to lease line and only web &FTP traffic out to ADSL.I configured b...
We are a company of 100+ with HQ and 6 other locations. We currently have T-1 in all locations but use Terminal Service to connect to the main computers at HQ. All locations need real time connection but they continuely get disconnection using TS som...
I am installing the WIC-1DSU-T1 V2 in a 1720 router and it is not showing up (no lights, no mention in sh ver or sh int). I am pretty sure the card is good, I tried dropping it in a 2821 we have and it looks fine. I also tried swtiching slots on the ...
Hi all,I've been experimenting with the CDP/ODR timers and have come across something that is confusing me somewhat.Now I know that when using ODR, the actual IP route info is carried in CDP advertisements. Therefore, you can't really send ODR adver...
http://img430.imageshack.us/my.php?image=hypertermianl0hd.jpghttp://img61.imageshack.us/my.php?image=crt0iy.jpgPlease look at the two links aboveWhy with HyperTermianl do I need to configure "flowcontrol" to "None".While in SecureCRT I have to config...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-12-2024 08:55 PM | ||
09-12-2024 01:10 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM |
User | Count |
---|---|
9 | |
9 | |
9 | |
3 | |
2 |