Hello, I'm looking for except script That will able to run command show run int g0/0.x on 4,094 vlan's ThanksRouting
Hello, I'm looking for except script That will able to run command show run int g0/0.x on 4,094 vlan's ThanksRouting
1. Why area 0 is required? Per RFC 3509 two non-backbones area cannot communicate and to ensure a loop free topology in a multi area design, especially with redundant paths , we need a central point and a reference to calculate the best path without ...
Hi, I have a new cisco 4221 router .I put in passwords during initial configs and an IPUnfortunately, now it cannot accept passwords and i cant access it using GUI yet i can successfully ping it.I have tried several recovery methods using SSH, Serial...
Hi Sir, I need eight 1G port and enght 10G port in the ASR 1001HX (or in the 1002HX). How many port license should I buy? Thanks. Justin
I have 'had' a situation where I have a class configured with bandwidth remaining percent and a policer.class INTERACT bandwidth remaining percent 9 random-detect dscp-based random-detect dscp 26 32 40 10 queue-limit 128 packets police cir perce...
Hi all, I need to configure this command "service-policy output X" to different IPSEC tunnels. I can apply it to all tunnels, no errors. But if I do a "show policy-map interface", I see only one tunnel Router: cisco ASR1002-X (2RU-X)Config:rtcore(con...
So if i have two routers and each router has lets say 2-3 computer devices.I am connected to the 1st router. So if i want to connect from my device to a device on the 2nd router than I will send the request to the public IP of the 2nd router. How doe...
Network: 10.0.0.0/24I decided to divide it into 4 sub-networks:10.0.0.0/2610.0.0.64/2610.0.0.128/2610.0.0.192/26If I have to configure static routing on an external router, can I use the network 10.0.0.0/24 in destination or I have to put all the sub...
The Cisco router prompt shows only that I am configuring a line: config-line.How can I make IOS to print exactly which line I am configuring?
Hi, I have a CSR100v with a 500Mbps throughput license on. If that license expires before the updated version is added, what will the device do - is there a grace period? Thanks
Are there guidelines/recommendations for the maximum number of items in an access control list in a given family of routers?Looking for input on various groups (1600-1800; 2500-2600; 3600-3700), if available, so we can do some custom ACLs and make su...
Having a problem getting Router 3 to communicate to Router 1. From PC5, I can ping Router 3, but cannot ping Router 1 from PC5. Oddly, I can send packets from PC5 to Router 1 so I am not sure what the problem is. Router 1 Se0 address: 10.0.0.2Route...
Hi,I try to get bgp prefix counter information of our internet edge router Cisco 72xx [IOS 12.2(31)SBx] via snmp but I don't know which MIB and OIDs match to the information of the following show command:===router#show ip bgp neighbors BGP neighbor i...
Hi,I tried using this command on the outside interface of my 887VA dsl interface and it stopped all traffic until I removed it. interface ATM0.1 point-to-point ip address a.b.c.d 255.255.255.252 no ip redirects no ip unreachables no ip proxy-arp ip a...
Hi,I'm configuring IP SLA in Cisco Router to ping 8.8.8.8 , any idea how to specify the ip next hope?Thank you
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM | ||
07-02-2024 04:20 AM | ||
06-28-2024 11:08 AM | ||
06-28-2024 06:23 AM |
User | Count |
---|---|
17 | |
5 | |
4 | |
4 | |
2 |