Can anyone tell me the meaning of the interface command:ip rip advertise 15It is configured on various interfaces but it is not documented on CCO. Does it mean that RIP advertises routes every 15 seconds? the IOS version used is 12.2SX
Can anyone tell me the meaning of the interface command:ip rip advertise 15It is configured on various interfaces but it is not documented on CCO. Does it mean that RIP advertises routes every 15 seconds? the IOS version used is 12.2SX
Hi all, I wanted to upgrade ios from rommon mode on 2600 series . i tried by setting all tftp variables . but no result . ?pls advise me how do i set variables or any other workaround?rgds,RAJESH
Hi all?how to perform loopback test from router serial interface to csu/dsu?, so that i can conform my serial interface is ok?Rgds,Rajesh
I need to know what LC=down CA=down TM=down LB=down TA=up LA=down stand for. They show up at the botton of a sho int hssi out putsh int h5/1/0Hssi5/1/0 is down, line protocol is down Hardware is HSSI MTU 1500 bytes, BW 45045 Kbit, DLY 200 usec, ...
Hello, I saw earlier message that this is a new feature to track the next hop reachability. I run into this exact scenario and would like to ask for help.My case is that I have a hub site with a ISP connection, so a internal WAN router on the secure...
I have HSRP running fine between two 3725 routers and I only want a way to make the ethernet interface down when the serial interface is down.So that a core swich ,which these two ethernet interfaces are connected to,will route certain traffic to ano...
Hi,I would like to use GLBP between the 6509's with sup 720 instead of HSRP,As you guys know ,to implement GLBP the physical interface of the forwarder should support multiple MAC address.Can any one suggest how to find whether the physical interface...
Can I install SDM on my Cisco 1751, if I have IOS Version 12.2 (2)XH. If not, where I can get the upgrade. Do I have to pay for upgrading the IOS ?
I'm trying to understand all variables that I should concern while troubleshooting a Multilink PPP problemin a scenario where a MLPPP bundle, with two CE interfaces associated to it, connecting a CE to a PEhas one of the CE connections suffering an i...
We had purchased this module to do channelized T3 to multiple remote T1 sites. I'm starting to think now that this module will not do channelized T3 (it is in a 3845 router). Am I right?
Is there any problem to use bgp private AS when multihoming to different ISPs and advertising the IP addresses assigned by one of the ISPs. On RFC it says that Private AS should be used only when singlehomed.Can someone give me any explanation about ...
What are the differences between the 3640 and 3640A routers? How can I tell which model I have?
We currently have 2 cisco routers, each router has 2 10/100 ports and 1 10mb port.They are linked via fastethernet 0/0 and also ethernet1/0.(there are some wireless bridges in between the routers connecting to these ports)The primary is fastthernet 0...
I am running IBGP between RTA and RTB in AS 100. I am using the bgp network command to advertise network a.b.c.d into bgp on both routers.RTA is an EBGP neighbor to ISP A in AS 200, and RTB is an EBGP neighbor to ISP B in AS 300.How do I control the ...
Hi, i need to create two different vlans on my 4506 switch(ios based)....one will vlan dedicated for ipx traffic and one for ip traffic...<ipx for novell machines>, how do i do this..pls help.Thanks & RegardsMax
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-17-2024 11:42 AM | ||
10-16-2024 07:21 AM | ||
10-16-2024 12:58 AM | ||
10-15-2024 08:44 AM | ||
10-10-2024 12:41 AM |
User | Count |
---|---|
12 | |
9 | |
7 | |
6 | |
6 |