hi,i need to "downgrade" an ASR1001-x from 17.2.1 to 16.9.7.do i just configure the boot system variable below?no issue with ROMMON code as it's already up to date. conf tno boot systemboot system flash bootflash:asr1001x-universalk9.16.09.07.SPA.bin...
Forum Posts
Resolved! Segment Routing-MPLS (SR-MPLS)
dear all,currently I am configuring segment routing MPLS with ISIS on Cisco router ios xr 6.3.1. everything is okay, ISIS is set and pingable , SR global bock is configured, Segment routing is enabled with ISIS, prefix-SIDs are configured with ISIS. ...
Hello Guys, I am currently having a minor issue with the ASA Firewall i cant get the ping reply to get through the firewall. It might be the NAT issue but i cant tell because i am too inexperienced. I can see the packets going past the firewall and w...
I've been working on configuring an ISR 4321 and I need to allow our Web Server to utilize a Public IP Address from our ISP, say x.x.x.34. I'm not sure where I should assign the Public IP Address. Should I make it the VLAN 3 ip address or the encap...
Hi guys,I've got a Cisco 2612 router and trying to route traffic between my Ethernet network (192.168.1.0/24) and TokenRing network (192.168.2.0/24). I'm trying to create a bridge between both networks. The router has the interface Ethernet0/0 conf...
I have a Cisco ASR 920 that is handling a 10G handoff from an ISP and then providing a 1G link to another router that is providing DMVPN services for remote locations. During times of load (from my testing I'm generating traffic from a single site),...
Hi, I have an ASR(A901-6CZ-F-D) that At&T Passes traffic through. They are saying there's up to 7% packet loss for them in an hour at this site. I have many sites that provide this same service but this one is causing them issues. I'm not noticing an...
Hello,I'm going to replace my simple modem router that I get from my ISP (Basic Phone Infrastructure)I have a difficulty to find a modem router that has:VDSL2\ADSL2+ modemBe able to work with the ISP phone infrastructure(I think it is Annex M not sur...
For a project I thought the ASR1001-HX would be the right one but then I noticed that the C8500-12X might be a good alternative. The choice would be to configure it without any Cisco automated tool, sorry guys I'm new to computation for the memory re...
Resolved! No internet for Clients C1111
Hi guys,router connects successfully to the internet, i also can ping WAN destination from CLI. But no internet for clients on Ethernet POrts. Current configuration : 5787 bytes ! ! Last configuration change at 07:58:19 UTC Fri Nov 12 2021 ! vers...
Hello everyone, I am having issue with Cisco 1841 router. Before I assigned a static IP to that particular computer(server). It was working fine. Port forwarding was also doneand it was working. No issue at all. But now I got issue. I am not able to ...
Hello all, I have cisco 2911 router with public IP enabled.I am able to connect my router through putty SSH using my private IP, and it works fine.But when I try to connect the router using public IP from outside the network, it says "Network error: ...
Hi, I'm trying to achieve totally simple thing - NAT between VLANs... I have one testing scenario where our QAs need to have all traffic from one VLAN NATed (hidden) as another VLAN IP, but I cannot do it on firewall as I need to keep 10gbps speed (a...
Recently I started upgrading 1900 routers (IOS Version 15.5(3)M5)) to C1161X-8PLTEP (IOS Version 17.3.3) . The config from the 1900 to the 1K ISR stayed almost the same, it was mostly a copy and paste. I’m using DMVPN to connect over 20 branches to 2...
