Hola.¿LLegó alguien a intentar configurar rutas estáticas en un equipo:C850-ADVSECURITYK9-MVersion 12.4(15)T7?
Forum Posts
Resolved! BGP problem
i can't ping from r1 to r6 or vice versa although this routes exist in the routing tables create pingable AS1 ---------------------- conf t hostname R1 int s2/0 no sh ip add 10.0.0.1 255.255.255.252 int s 2/1 no sh ip add 10.0.0.5 255.255.255.25...
I am having 2 issues in this lab. R1 and the NXOSv are running BGPOn the Nexus the eBGP is running inside the VRF “TEST”R2 is running EIGRP with the NXOSv (Global table of the NXOSv) Issue 1: I am unable to leak EIGRP routes in the BGP – I do not se...
Resolved! Traffic being assymetric and CEF
Hey Guys,I have configured BGP multipath to get BGP load balancing between two ASs on my company.The scenario is in annex. Basically i have two routers interconnected with 2 links running in different ASs.BGP multipath was configured so that i could ...
We have a project for a client, where it interconnects 2 concentrators with ASR1001, plus 16 branches with ASR920 4SZ-A, all units are inside a vrf in Algar's MPLS network and Tunnels were created to separate the traffic from these clients, however w...
Hi newbie here... Just recently started on an all around IT job for a small company. I noticed the router's IOS were way behind. Latest seems to be : Release 15.7.3M6 MD Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.6(3)M, RELE...
I know about floating static routes and how they works. I want to have default or static route to same destination over two different interfaces towards different gateway. One will be active and other will be passive. But both needs to be in routing ...
Hello together,I have a Cisco 819G Router 4G LTE, I want configure an internet connection. What points do I have to configure? What do I have to enter here? lock or unlock?cellular unit lte sim { lock | unlock } pin #show cellular 0 allProfile 1 = IN...
Hello Everyone, I wanted to ask whether BGP multipath feature works for a route learned from eBGP and iBGP neighbors. Please see the topology below. In this topology, Router C learns 10.0.0.0/8 from A via eBGP and from D via iBGP. Can both paths (via...
Hi, Wondering if somebody could explain something. We have a pair of C1111-4P routers. they are acting as a ZBFW. We have redundancy groups configured on these routers so they act in a HA pair. The primary router has a priority of 110 and the sec...
Resolved! ACI OSPF neigbor stuck in Exchange/DR
Configuring OSPF neighborship between ACI and Catalyst 4507 switch but the neighbors are stuck in Exchange/DR. The MTU on ACI is 9000 by default and on Cat4k is 1500. I did configure 'mtu-ignore' on both sides and still unable to bring the neighbor u...
Resolved! ASA not advertising routes
I'm having an issue where my ASA isn't advertising routes in eigrp. The interface is up (Gi0/3), and the network is being advertised (network 172.16.10.0 255.255.255.0) in the correct autonomous system (AS 1).Its almost like the interface isn't allo...
Working Config .. Router RV325 , only WAN1 in use for Internet Access. LAN inside incl. DHCP 192.168.1.XXFor a dedicated IP address 10.209.157.0 Subnm 255.255.255.0 a static routing is defined... to 192.168.1.254Reason: on 192.168.1.254 a Cisco 80...
Resolved! upgrade CSR1000v steps
hi,I am going to upgrade my CSR1000v. and I have done this many times before. but I just found a link below. https://www.cisco.com/c/en/us/td/docs/routers/csr1000/software/configuration/b_CSR1000v_Configuration_Guide/b_CSR1000v_Configuration_Guide_c...
Resolved! How Do Routers Handle Access Lists
Hi, all. Just a quick basic question. I'm aware of how L3 switches handle standard and extended access lists, where the entries are used to populate the TCAM and multiple ACEs can be processed simultaneously. I'm not sure how routers carry out their ...
