Hi, Seems like I'm having this weird issue on my network that a specific IP block under switch1 vrf cust instance experiencing some delay or issue when accessing/connecting to a public proxy server and sometimes this cause delay when browsing using t...
I have a friend that thinks that the CIsco 4431 ISR is about to go end of sale. Any thoughts?
HI all, I came across the below configuration on my wan router which has two uplinks through 2 isps.Can any one help me to understand how set ip next-hop verify-availability command works .route-map abc permit 10match any set ip next-hop verify-avai...
Hey,I own a small business and got a 2nd ISP. I have a RV340 up and running: WAN1 - VDSL (modem in bridge mode) PPPoE (175mb/s)WAN2 - Cable with static IP (1000mb/s)Load-balancing is set to WAN2 80%, WAN1 20%I added VLAN11 on eth3 for IPTV with dhcp ...
Hi. By default, Is there a "deny any" at the last line for all ACL? for ACL 2, will it allow all? access-list 1 permit 202.160.198.192 0.0.0.31access-list 1 deny anyaccess-list 2 permit 202.160.198.192 0.0.0.31Thanks!
Hi Everyone I have been researching the forums and some models come to mind. Basically i am after a CISCO router that will happily handle a 350Mbps internet circuit.- Will have about 30 NAT and PAT rules- 5 vlans- 50 users. - slash 29 wan subnetRegar...
Hi All I have set up a branch using the IWAN app. On the App, we are supposed to be able to get the health of the applications and what is flowing etc. We have Cisco Prime and APIC IWAN app talking to each other and all devices are sending Netflow. H...
Hello Everyone, I have an IT testlab with a Cisco 880 VA router. It has 4 switchports (FA0-3). I use these switchports only, as for some reason I can't configure the atm/eth0 port.Configuration: I have got two Vlans: Vlan1 and Vlan2. FA/1, FA/2, FA/3...
Cisco Community, I'm planning on using an N9K as an L3 switch\Router at my smaller datacenter locations and plugging my transit provider directly into it. My transit provider provides a full table and this obviously will not work with an N9K. Do yo...
hi,i got a router which has AAA and MGMT interface using a VRF.i noticed some routers has MGMT VRF configured but not under its AAA 'ip vrf forwarding'i need to add the said command under AAA to generate/monitor logs in ISE.my question is, will i get...
Hi everyone,this few months the router keeping blocking our company user outlook email all user suddenly fail to send and received the email, outlook just keep pop up the error box Task"xxxx@xxx.com" receiving reported error (0X800CCCC0F) . every tim...
Hello, I know that route injection let us to insert prefixes more specific withouth appear in the routing table. Now I am practising but isn't working fine. The steps are: Configure a prefix-list listing all more-specific prefixes Configure a ROUT...
Hi all, I would like to ask, if I can set-up redundant ports on Cisco Firepower 1120 ? My scenario is : I would need to connect this device to 2 ISPs . And when one ISP (connected to 1 port) goes down, all traffic should be redirected to go through ...
I have to do the following topology on packet tracer, I use the student edition:topology I read the ospf protocol with mutli areas and I understand many things. But first I can't do the above topology on packet tracer, when I statically make the ip r...
Dear All, am using cisco 871 router. c870-advsecurityk9-mz.124-24.T1.bin presently used ios, i have few doubts 1. can I update my image to the latest version in this router ?2. where should i find the ios , i searched a lot unable to find any image ?...
