Hello Community, I have a query about Sdwan AAR ( application aware routing ) . I have a sdwan setup with controllers on premises and may setup looks fimilar to below detaisl . Branch --> MPLS Provider --> DC --> DC FW--> Internet . I want to find a...
Forum Posts
Hello , Could you help to answer my below queries ? 1) If we have multiple DTLS connections to V-smart then over which control connection OMP Peering will formed ?2) How V-edge select single transport out of multiple transport to form single contr...
Hi, The interface stats can be retrieved via /dataservice/data/device/statistics/interfacestatistics call (an example data record can be found below). Most fields in the response are clear, but can anyone provide even a rough explanation what's the v...
Hi,Is there any good solution with SD-WAN on Internet Edge Routers for controlling the outgoing traffic to the service providers from the customer side? (except using PBR solution)And how does it exactly work ? We want each buildings send/receive tra...
Have a customer that is looking to migrate to an SD-WAN based on the new Catalyst C8200 platform.The current ISR4K's support FXS/FXO and SRST for their CUCM environment and the C8200's that we are planning will have the needed FXS/FXO ports.Is there ...
If I have two totally isolated network.. say one color private1 and the other private2.. and no communication path between the networks... can I simply have a HUB and Spoke design where the Hub is connected to the private1 and the private2?... Th...
Hi, My company is running Nagios network analyzer.I am wondering if Viptela SD-WAN Edge supports Nagios network analyzer as Cflowd collector.
Hi all I my trying to connect my vsmart to my vmanage and Im getting the issue, im using version 19.2x They are in the same Ip range and same site. "Sync Pending - Device is offline" [5-Dec-2019 19:27:23 UTC] Starting Checks.[5-Dec-2019 19:27:23 UT...
IT seems like there is a lot of hype surrounding SDWAN putting pressure on companies to migrate their existing infrastructure away from something that was working and got the job done (such as DMVPN). I understand SDWAN can benefit with route and mul...
I'm trying to figure out how exactly nPing works under vManage GUI> Network > Troubleshooting and why RTT shown from its ping output and what the managed router tells me is completely different. I noticed this when I tried to test ping from one of i...
Can't seem to find the tool in CCO or via a Google search, where is it located?Its specifically mentioned in the below whitepaper on page 9 and 10 https://www.cisco.com/c/dam/en/us/solutions/collateral/enterprise-networks/sd-wan/white-paper-c11-74107...
Hi Friends , I want to setup my vmanage in active standby mode . Both my Vmanage are in different geo locations . i did following steps till now :- Added root certificate in both vmanages ( both location vmanages ) . added Vsmart and vbond in Primar...
Scenario: - Service VPN connects to a LAN with a prefix which is routable on underlay network (say MPLS VPN) - NAT on VPN0 uplink interface (facing MPLS) is not enabled - eBGP peering is established over uplink and exchanging routes properly ...
Hi, We have 2 Edge Routers and 3 ISP connections, which are connected to both of these routers, as the image bellow.Now we want to have symmetric traffic. Our Provider Independent IP Address is X.X.X.X/22, which we have split it to 4 X /24 addresses....
I am running csr1000v version 15.5(2)S with IOS-XE version 03.15.00.S on Ubuntu 20.04 LTS. My csr1000v is currently under no license. I can configure bfd on the GibabitEthernet interface and the OSPF router but cannot configure bfd in the DMVPN tunne...
