We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board from June 18th - July 18th. These dates are subject to change pending progress. This in...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
"Minor", but irritating as it causes a bunch of NMS software to get fairly upset. ifIndex and ifDescr from one of our sg300s look like this: {49 "gi1",50 "gi2",51 "gi3",52 "gi4",53 "gi5",54 "gi6",55 "gi7",56 "gi8",57 "gi9",58 "gi10",59 "gi11",60 "gi1...
We upgrade our device firmware to keep up with the latest releases. In upgrading RV320 firmware from 1.4.2.19 to 1.4.2.20, we are having trouble connecting via the GUI.We have a running configuration on 1.2.2.19 that has the Firewall HTTPS box NOT C...
Resolved! RV320 Private LAN Address Range
I tried to set up an RV320 using 172.30.2.0/24 on the LAN - which is in the private address range of 172.16.0.0 – 172.31.255.255 I got the impression that it didn't or wouldn't work as I'd tried it more than once. Using 192.168.111.0/24 did work righ...
Resolved! Changing SG300 from Layer 3 to Layer 2
Will changing an SG300 switch from Layer 3 to Layer 2 cause any significant user downtime, or any at all? I have two 52-port SG300's and two 20-port SG300's to make this change to.
Hello,I have a network where by I have been given a LAN block 66.157.179.160/252 and serial IP by my ISP. I have successfully configured one of the 550 ports with the correct serial IP addr and gave a default route to the remote serial IP so from th...
hi guys, during some testing of a SG550XG I`ve detected some questions, which I was`nt able to figure neither with the CLI nor the Admin Guide... in the DEFAULT configuration there`re some lines which I do not understand (= because I´ve not build up ...
HiI have switch SG300-28. Before update firmware i had versdion 1.3.6 and on this fw was option to copy running config to backup....Also on 1.4.7.6 it looks like: Now i update firmware to 1.4.9.4 and boot 1.3.5.06 and this option was removed ?look as...
hi guysI upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I ...
Hello. I've managed to collect information piece by piece on forums, MIBs, boards etc and make work reading status information from this switch into some managing software.Now I'm stuck on setting vlans or port:Common OIDs "vtpVlanEdit" section (1.3...
Hi Community We have 2 units of "SG550XG-48T 48-Port 10GBase-T Stackable Managed Switch" in native stacking mode.We have to reboot the whole stack, but we want only reboot unit 1 and then after i few minutes unit 2. This because we have LACP enabled ...
Hi,I'm working with AV company dealing with Crestron and Dante audio combo . I normally enable edgeport on SG300 and we never had any issues with Dante devices after reboot or unplugging/plugging devices to the switch. Dante controller shows all devi...
We have a few several-years-old Cisco Series 300 series switches, 100Mb Ethernet PoE, that we are looking at replacing. One 48-port switch and four 24-port switches. What is the difference between the SG300 and the SG350 series -- besides price?? I'm...
Resolved! 3560-CX strange/incorrect temp reading
We recently got a 3560CX (WS-C3560CX-12PC-S). Where it is currently situated seems extremely hot. So to check the temp we logged onto the switch but received the following which does not make sense: According to this we would not get an error until...
Resolved! SG300-28 without fan - add fan and temp
HiI have a switch sg300-28 without fan and not show temp. I see that in motherboard is point to solder plug for fans and I test and it give on one pin 12V and on second about 3.3V.Is any chance to solder plug and connect fan. It works ok but in GUI n...
Good morning, according to the CLI manual, release 1.4, page 980 ff. there is a "show environment" command similar to regular Cisco switches. When typing this command in the CLI there's a "Unrecognized command" error message. Is there any way to get ...
