We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hi, I'm using old C2960G-24TC-L running 12.2.55(SE12) for non-critical task. I hope the OID for this exact model would the same for all 2960 in the same generation. But I will also have to find OIDs for 3750 & 3750v2 running also 12.2.55(SE12) ...
I have my 5 branch offices connect to my main office using NLAN. Each branch office has a 50M connection to our provider, and connects to our main office on its 250M connection. For simplicity, I will only include 2 branch offices - one that works ...
I have a problem connecting the SG350 to a HP Comware switch (A5800). I have quite few SG300 switches and they work OK when connected to the HPE A5800. Recently I've got a new SG350 and trunk port configuration doesn't work. Port on HP switch is conf...
Hi and thanks for reading. I have one SLM248G Swtich wich has two routers connected to: Router A in port e32 and Router B in port g1. The first one works just fine. But Router B has packet loss only for VLAN ID 20. Traffic capture at Router B sho...
SG300 switch Hi, Currently testing the IP Source Guard feature and planning to eventually roll it out in our network if all works well. I'm doing minor steps and I'm currently trying to enable source guard through the web interface on a specific ...
Hi every body , Here is my problem: I have a SonicWall firewall - (192.168.2.1 / 21) Below I have a switch layer 3 (192.168.2.37), I'm setting some vlan: Vlan30 ip 192.168.30.1/24. I activate the routing: Ip routing roads: I tried several thi...
Hello,Anyone knows the default password?Thanks,
Hello, I am trying to set up a switch to carry two different subnets (.10 and .20), with each on their own VLAN to avoid any contact between the two. Each VLAN is being carried in on its own ethernet cable, to ports 11 and 12, respectively. Individu...
hello I'm Harry I'm korean so I'm not good at speaking in English. Anyway I have some questions about sg300 I want to ping from valn1 to other vlan's without a router.As far as I'm concernd, normally switch can use a "ip routeing"commend but I can't ...
Resolved! did I brick my SF300-08?
I got assigned to manage a rack that includes a Cisco SF300-08. It was working fine. I needed to login to it, but the previous admin did not leave the user/pass for the switch. The defaults of "cisco/cisco" didn't work. So I looked up how to ...
Hi Team I have been asked to configure Cisco SG500 switch with initial setup. I did complete the configurations except for stack ip address. Need support how to configure stack ip address to switch. Thanks Srinivas Patnaik
I have a SG110-24HP-NA unmanaged switch, purchased used cisco IP phones model #7960 and am trying to get the phones working. I have charter as my internet provider using a Arris TM804G modem. Phones are not working, what am I missing?
Hi there. I have Cisco SG500 in L3 mode. Now I need to get ip addresses for vlans from two different external dhcp servers (for ex. 192.168.1.21 and 10.17.10.10). For Cisco Catalyst it would looks something like this: int vlan 100 ip addr 10.100...
Hello.I bought the SG200 switch and the Sg300-10 switch.It supports POE.Of course I have enabled jumbo frames in the port settings.(on the Web)But my GiGe camera does not get good images.It works very well when i replace it with a Netgea...
Hi all! How do I delete Vlan DB on sg300-28 ? Note: The Startup-config file was already deleted from flash
