my wireless laptop from surabaya cant connect to Yogyakarta computer or Jakarta server. can anyone help me to resolve it?here's my pkt file
my wireless laptop from surabaya cant connect to Yogyakarta computer or Jakarta server. can anyone help me to resolve it?here's my pkt file
Hello, I'm new Cisco user. I have on Cisco 350 Switch. I created three VLAN (10, 20, 30). On VLAN 10 I entered IP from subnet of my Internet Router (non CISCO device). If I connect client to this VLAN via CISCO Router, it connects to the Internet (DH...
We have a 3850 at a remote site that has been working for quite some time. The uplink back to the central site is a 4 port SFP module with a single LC fiber cable and a GLC-SX-MM SFP module. Yesterday and today, the uplink port went down/down and the...
Hello All, I am applying QoS on interface that has traffic going, BPE_LAB_C1111x_0002#sh interface g0/1/6GigabitEthernet0/1/6 is up, line protocol is up (connected)Hardware is C1111X-ES-8, address is ac7a.5622.9a0e (bia ac7a.5622.9a0e)Description: R3...
My network consists of cisco catalyst 3850 24 port switches used as the routers between my sites. I am out of 3850s and need to add a new site. i do have some 9300 switches. My question is can i add the 9300 switch into my network as a router without...
PMDoes anyone know what the following means that shows vty0 as a user ?While further down in the last commands the user that exists in cpe is normally shown.Basically I'm looking to find out who threw the commands with vty0@vty0358 1 vt...
Hi, We have started using C1121-8PLTEP in our branches. Today needed to use the PoE for the first time. Cannot get power on any of the 8 ports. This looks ominous:sh powerMain PSU :Configured Mode : N/ACurrent runtime state same : N/APowerSupplySourc...
I used to be able to do a "show arp vrf all | inc x.x.x.x in the 9000 series routers. We recently switched over to 8500 series. It appears I can't do that command. Is there a work around?
HiI am building an home laboratory with some routers.I'd like to know if can I connect Cisco 1841 with WIC-1T interface to a Cisco 2921 with HWIC-2T interface?The true cable should be CAB-SS-2660X?
What is the configuration for cisco 800 router to techroute router failover configuration in mpls link
Hi, We have CISCO IOS XRv9000 installed with FW version 7.3.25.I tried to create a ssh connection and started with creating a rsa key:#crypto key generate rsaWhen I ran it, I was getting "Operation not permitted" error on the console.I was running th...
I have the following network; A ring backbone consisting of Nokia Routers running multiprotocol BGP, MPLS, LDP, SDP, VPRN service. The Sites would run a Cisco Switch that communicates with the Noka Router through BGP.The Cisco switches can communicat...
hello,I want to access to servers which are connected behind my router Cisco ISR LTE/4G.On the process creating the hostname, it tells me to fill a public IP address but i don't know why because the IP on the router is dynamic and changes every time....
Hi!I have to setup an outbound shaping for a Telekom ethernetconnect line on a C9200L-48T-4X . It has the following parameters:burst size: 60.000 Bytesspeed: 1 Gbit/sAccording to this data sheet: https://geschaeftskunden.telekom.de/magenta-business-n...
I have a plain Cisco 3650 switch. I need to transfer the running config from this switch to a PC running SCP (Solarwinds)The PC is directly connected to the switch & the ping is reachable between the switch and the PC.SCP is enabled in the solarwinds...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-17-2024 12:44 AM | ||
09-12-2024 02:06 AM | ||
08-28-2024 02:25 AM | ||
08-20-2024 09:12 AM |
User | Count |
---|---|
10 | |
9 | |
7 | |
5 | |
5 |