Does anyone know the difference between the U and UB designations.C9300-24-U or C9300-24-UB What is the feature differences.I know these are both UPOE ..
Does anyone know the difference between the U and UB designations.C9300-24-U or C9300-24-UB What is the feature differences.I know these are both UPOE ..
Hello, Palo1(Active)(Inside seg) >>>(L2? L3-p2p?)7K1(VPC) Palo2(Passive)(Inside seg) >>> (L2? L3-p2p?)7K2(VPC) How should this be done in order to maintain redundancy? Create a new SVI and VPC for the inside firewall segment, then configure the f...
Good day all - please see what i used to attempt to gather netflow from a switch; my question here is - why do i see traffic from all my other branches from this one location? flow record record1match ipv4 protocolmatch ipv4 source addressmatch ipv4 ...
Hi, I have some new 2960-8TC-L and I would like to upgrade them with the following firmware: c2960-lanbasek9-tar.122-25.SEE3.tar but it's not possible because the Min.Flash which is needed has to be 32MB and this is what I have : switch#dir flash:Di...
Hi Friends, I am looking for EOL and EOS for Cisco Model WS-C3850-24T. whether EOL/EOS differ depends upon Software version? mine is below. #sh verCisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIV ERSALK9-M), Versio...
Dear Community, I have one piece of Cisco SG250-26 port that got stuck booting with System LED blinking and no progress. If there is any knowledge on how to boot from USB or how to get it back into senses please let me know. Many thanks in advance.
Can we run OSPF on above device which has IOS of Essentials
I have a Cat 5e connection to a GB Netgear switch and it blinks green. When I show the interface it says 100 Mb/s full duplex connection. I ran a Cat 6 connection and now it blinks amber, but the interface still shows 100 Mb/s full duplex connection...
Hello I am getting this following error and get ACTV, XPS and S-PWR LEDs amber then suddenly all LEDs are off: Booting...(use DDR clock 667 MHz)*** Coprocessor Unusable Exception ***PC = 0x00000000 00000000SP = 0x00000000 00000000Cause Reg = 0x00000...
Hello everyone! I'd like to know can I upgrade WS-C3650-24TD-S switch (IP Base licence) to IP Services licence for this one?
Hi, I am finding a hard time finding ISO version compatibility. Can I go from current running ISO version: 15.0(2)SE6, 15.0(2a)EX5, 15.0(2)SE8, 15.0(2)SE8 TO 15.2.4E8 MD? Switch models: 2960-C and 2960-X (24 & 48 ports). Thank you.
We are a small organization that bought into 4506E chassis switches for our networking about 10 years ago, mainly due to the 10 gig backbone capability. As I expect most people with 4500E are aware, the 6L-E supervisor goes officially end of life in ...
Hi there,Thanks for reading. I'm having trouble stacking 4 members into a C9300-48U stack. I have redundant PSUs installed and powered. I have all four cables with the Cisco emblem upright (and notched side at bottom). I seated all ends with a nic...
Hi, I am planning to implement qos on WS-X4590-E with WS-X45-SUP6-E Supervisor. IOS 12.2(50) I will be marking couple of application to AF21 and also prioritize voice packets, signaling packets against the ACL. Q: There are users connected on this ...
Recently replaced a 3845 in my Data Center with a ISR 4331. Used the same Fiber SFP that was in the 3845 in the 4331. My network monitor is showing my WAN interface and completely down. This is the output from the sh interface:DALLAS-4331#sh int g0/...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-11-2025 08:26 PM | ||
05-27-2025 03:30 AM | ||
05-27-2025 12:59 AM | ||
05-23-2025 10:30 AM | ||
05-15-2025 09:37 PM |
User | Count |
---|---|
12 | |
9 | |
6 | |
5 | |
3 |