I gave the IP adresses PC0 and PC1. And I would like run this command show interfaces f0/1 counters and doesnt work.
Forum Posts
I have a few SG300 switches and I have a bit of a problem. I'm not really sure where to look for the issue. I'm convinced it's got to do something with the config I have for our switches but let me explain the issue and see if you think the same. We ...
Resolved! Untagged traffic on native vlan
Hello, it's my first time posting here and I will very much appreciate your kind response guys. I was just wondering how does a switch handle untagged traffic? If an untagged tragfic from a vlan passed through a trunk going to another switch, will th...
Resolved! Stack 6800IA FPD with FPDR
Hi All, Would like to ask, is stacking 6800IA-48FPD with 6800IA-48FPDR possible/recommended? Thanks very much
Hi All, I have a Cisco Catalyst 9300 which is dual attached to a distribution switch using a port-channel. I need to configure auto qos on the port-channel uplink to support a voip deployment. I have read in the Cisco 9300 IOS-XE release notes that a...
I have a Pair of N9K-C9372TX-E's running 7.0(3)I4(8a). The EPLD info indicates : Module Type EPLD Running-Version New-Version Upg-Required 1 SUP IO FPGA 0x06 0x06 No 1 ...
Resolved! EIGRP Neighbor Not On Common Subnet why?
I have two switches running EIGRP but get the following error messages *Mar 6 16:06:19.511: %DUAL-6-NBRINFO: EIGRP-IPv4 100: Neighbor 172.18.8.1 (Vlan3) is blocked: not on common subnet (10.32.253.17/28)*Mar 6 16:06:33.266: %DUAL-6-NBRINFO: EIGRP-IPv...
Hi I need a Layer 2 Isolation for the guest vlan on some catalyst ws-c2960x switches (are connencted via trunk ports) for the customers Ubiquiti unifi APs. Here are my config for the public wlan vlan, i need that the vlan 102 can only see the Ga...
Dear all, After booting the 4500-X switch showing the below message and the switch shutdown automatically . Anyone knows the solution for this issue ? Press RETURN to get started! *Feb 26 23:10:33.922: %C4K_IOSSYS-6-IMAGELEVEL: Supervisor booti...
Hopefully someone can help me or advise. I presently have 2960S switches running in a mixture of edge switches generally running c2960s-universalk9-mz.150-2.SE4-6.bin and mixed 2960S/2960-X stacks running c2960s-universalk9-mz.152-2.E5.bin/c2960x-uni...
I need Knows if C9400-SUP-1XL Support VSS or StackWise Virtua ? I am researching and not find anything of vss, only Stackwise in some specific IOS not all
hi there, i want to test the embedded wlc that comes with the cat9k the model of the switch is: Switch Ports Model SW Version SW Image Mode ------ ----- ----- ---------- ---------- ---- * 1 40 C9300-24UX 16.9.2 CAT9K_IOSXE INSTALL i'm trying to in...
Resolved! my 2960S has problem with VLANs
hi. i use 2960S for test but few days ago, VLAN interfaces got down and up intermittently. so i looking for log about VLAN problem but there was nothing about information about this problem. just written like some vlan interfaces down and up. is ther...
kindly we have 2 2960x switch stacked and we have 1 fortigate 60D mode hardware switch and this fortigate don't support Link aggregation and we need to connect with fortigate by 2 uplink 1 from each edge switch and when we do this we create a loop be...
Hello Everyone, I have the below scenario: Two L2 switches - S1 and S2. Port f0/10 connected to PC1 on vlan 10 on S1. Port f0/11 connected to PC2 on vlan 11 on S2. Port f0/1 on S1 is on vlan 10 and is connected to port f0/1 on S2 is on vlan 11.Their...
