Switching

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

WAP131/321 on Cisco 3560 switch

Hi all. i am trying to connect cisco wap131 and 321 access point to cisco switch 3560 48port, as soon as i connect, the port turned off in 1 sec and turned on after 5 mins when i remove connection, this is happening with any port.  can some one help ...

theascott by Beginner
  • 128 Views
  • 1 replies
  • 0 Helpful votes

Help with ASA configuration

I am currently trying to build a network in a lab at ECPI and having issues connecting the ASA to the network and getting all LANs out to the internet. The outside ip address will be 10.14.11.155 with a default gateway of 10.14.11.1 I wanted to conne...

Resolved! OSPF router-id selection

iosv-8(config-if)#do show ip int brInterface IP-Address OK? Method Status ProtocolGigabitEthernet0/0 10.255.0.11 YES NVRAM up up GigabitEthernet0/1 10.254.252.2 YES manual up up GigabitEthernet0/2 unassigned YES unset up up GigabitEthernet0/3 222.22...

R1 can ping 3.3.3.3? Why?

Hi Please see the diagram attached. Do you think R1 can ping 3.3.3.3? Why? Please note static routing is a little different, the GW is 192.168.23.3 R1(config)#ip route 3.3.3.0 255.255.255.0 192.168.23.3R1(config)#ip route 192.168.23.0 255.255.255.0 1...

wfqk by Contributor
  • 385 Views
  • 11 replies
  • 0 Helpful votes

Spanning tree blocking port

Hello, I have a question regarding STP. When I connect switch from port 1 to port 2 (see picture), port 2 goes into bloking state and port 1 in forwarding. What I want to achieve is to make port 2 forwarding. Normally I would use : Sw(config)#int f...

andrepoko by Beginner
  • 150 Views
  • 3 replies
  • 0 Helpful votes

SG300-28P slow performance.

Hello,  I am not an experienced network engineer and I need some help with my home network configuration, mainly due to the fact is seems to be running very slow. I have a SG300-28P and attached to it are 2 x WAP561.  I have various different proble...

Resolved! Adding Subnets to ASA 5505

I am very new to configuring firewalls. I will be adding virtual servers to our network that attach to a Layer 3 HP 2920 switch.  There are also subnets configured on the switch (for the virtual cluster). I need to know how to configure my ASA 550...

Noisy SMPS in a WS-C2960C-12PC-L

Hello everyone, I've got a question about power supply noise caused by this device, supposed to be ... silent ;-) When powered, the SMPS (Switched Mode Power Supply) is very audible, exhibiting a random noise (like arcing). This is my first PoE comp...

FC Support on Nexus 56128P ???

hi friends, we have a nexus 56128P with ios release 7.1(0)N1(1a) , ( latest nx-os for this platform ) but we can not set port type to fc ( native fc ), what is our problem? how we can config ports as fc type? ( native fc )

Private vlan SVI routing

Hi guys, I have a question: I have a topology that goes : Host - > SwitchA - > SwitchB(Layer3) - > CORE NETWORK - > ISP Host want to reach the Core network, but from some reason it cant. Host can ping SwitchB SVI interface(which configured as defaul...

Resolved! native FC support ?

hi friends, we have a nexus 2348 and a nexus 56128p, ( 2348 will be our fabric extender ) FCOE is work fine but we want to config ports on 2348 as native FC type, what we need to do this? is "Storage Protocols Services Package" license enough for ...