Hello Everyone, Need to confirm if we require any license or our switch is capable for SVL configuration. Model- Cisco C9407R We have below license on the switch. Please let me know it is ok or not for SVL config. #sh license summary License Usage...
Forum Posts
Hello All,I work for a large (enterprise company). We have a location where we want to block internet access though ACL on our core. I have created a New VLAN with subnet 10.40.94.0/24 and moved all computers that should disconnected from internet. T...
I'm doing some spanning-tree training and I'm wondering if it's possible, in the packet tracer software, to set the MAC address of a 3650 switch. I don't want to just set 1 interface, because I want to control (not via priority but via MAC address) ...
I am wondering what the command would be for automating a shut, no shut on Cisco 2960x switches.I would need to target a few Gi #/#/# ports. Any good tested recommendations?
Resolved! Packet Tracer pinging
So I am working on this assignment and for some reason I cannot get V15 or V20 pcs to ping across the network they get stuck at Distribution 1. When I add default gateways to the switches and remove them they ping to distribution 2 but no further any...
I have two switches, switch 1 has vlan 10 and switch 2 has vlan 20, i don't configure anything on switch but it ping from vlan 10 pc to vlan 20 pc Pc1 ip 192.168.10.1Pc2 ip 192.168.10.2link between switches is not in trunk mode
Hi to all I have two switch, switch A (C9300) and switch B (C3850).Switch A has three vlan: vlan 2000, 3000 and 4000.Switch B has one vlan: vlan 1 (default) Switch A is displaying log with: CDP-4-NATIVE_VLAN_MISMATCH : Native VLAN mismatch discovered...
Hi guys,I need to setup a new little PoP in a DC which is giving me max 200W of power. In similar situations i usually put a couple of catalyst 3850 with stack config, for production traffic and a 3750 for management one. This build consumes around 2...
Dear All,We are planning to connect two VSS switches in different domains i.e switch A & B in one domain and switch C & D in another. Users will connect from Access to Switch C(Active stack) traverse through switch A to connect internet firewall an...
HiI have two Cisco 2960-x switches, one with 24 ports and one with 48 ports, both of which are poe. I want to connect my hp m402dne printer to the network. When I connect the printer to the 24-port switch, the printer's ethernet light turns on withou...
Hi CiscoTeam, I was trying to factory reset 9200 switches and they are in Rommon mode now, I did try to reboot them but they are looking for their stack switch and packages.conf file is not able to reboot the switch. Can you please help me recover th...
Hi, i have Access Switch C9200L-48P-4X-E and Interface G1/0/1 is Uplink Trunk to Distribution Switch however, we are getting the below error for some:%ILPOWER-5-DETECT: Interface Gi1/0/1: Power Device detected: IEEE PD: %ILPOWER-5-IEEE_DISCONNECT: In...
An organization is granted the block 16.0.0.0/8. The administrator wants to create 500 fixed-length subnets.a. Find the subnet mask. 255.255.128.0b. Find the number of addresses in each subnet. 2^15-2= 32766c. Find the first and last address in the ...
What is modularity in network design? (a) Ability to to create self-contained, repeatable sections of the network(b) Ability to scale and accommodate future needs of the networkHello Community, kindly help my understanding, I believe the answer to th...
We have a 2950G that has lost IP connectivity via the management IP. All ports, access and network trunks, are up and passing traffic but there we cannot reach via the management IP. Had been working previously and has gone up/down a few times. Ple...
