Hi everyonelets assume we have 2 cisco 3750x switches with 4 Gig interfaces to each other that are channled into Po10.3750X||||||||3750Xfor this scenario the etherchannel uses either mode ON or LACP and loadbalances based on src-dst-ip.using the comm...
Forum Posts
Hi all,I've experienced, recently and in the past, loop problems in my enterprise network, related to an access switch freezed. We still have access switches not connected through etherchannel to the distribution switches, which are in stack, so span...
Hello,We are trying to filter sources by mac and have two targets below.We want only whitelisted macs to connect to the switch and any other should not have access to any port.We want only IT admins Computers to be able to access management interface...
Hi. I need to install c2960x-universalk9-mz.150-2a.EX5 on a new switch we are purchasing that will be added to our existing stack. When I search for this particular IOS version I get taken to the Catalyst 2960X-24PS-L switch page on the Cisco website...
Hi Everyone,I have catalyst 1000 series switch which handles through which 70% of company's daily traffic goes. Issue is sometimes out of sudden, web GUI stopes responding (when i enter 192.168.1.250 which is the address of GUI, it keeps loading and ...
Hello everyone,I want to upgrade my Cisco C9200L-48P-4X device. Currently the firmware version is 17.6.5, which is the Bengaluru version. Can I upgrade to 17.9.x which is the Cupertino version?
I am facing an issue. My network gets unstable for a minute and port of one switch goes to error disable and reason i get is loopback. I am not able to identify the issue. i have enabled err disable loopback but it makes network unstable for some tim...
I have several stacks of 2960-X switches running various versions of IOS 15.2 code. I've been asked by our Telecom group to see if I can find out the power draw of the stacks in each data closet. I can pull some info via the "show power" command: ...
Hello, We have a switch connected to our operator's router. It's a 'OneAccess' router.What could cause the switch to see itself on the port connected to the router?SW#sh cdp neighbors Capability Codes: R - Router, T - Trans Bridge, B - Source Route B...
Resolved! Create ACL and routing
Hi I need help with my topology, so what I wantOnly this network (192.168.30.0/24) is authorized to have access for remote configuration for the switches and not the others.But I want all networks to be able to "ping" the "internet" routerCurrently ...
I have a 9300 switch with an Essentials license. It has a limitation of 1000 OSPF routes.Will there be a log to indicate that this limitation has been hit? I could not find any information on this.When I do show ip route summary to check the total nu...
Hello,I have 9200 IOS XE 16.x.x and 17.x.x catalysts on which I would like to set up CLI user authentication by LDAP / LDAPS server.My question is whether this is possible with only an LDAP server without any AAA server (TACACS +, Radius)?I have seen...
Hy AllI have a Nexus 3548x that is configured to work as an L3 switch.I'm trying connecting him (trunk & access) to my FortiGate using sfp.In all my tries im getting:Eth1/1 1 eth trunk down Link not connected 10G(D) --Eth1/2 1 eth access down Link no...
After upgrading a few 2960XR to the latest IOS (15.2.7E9) we have seen something that looks like a PoE negotiation issue with some G4S/Amag security nodes.After the upgrade it seems that the switch and the endpoint is not able to negotiate enough PoE...
So long story short just unsure on thisWe have users that have an unmanaged switch in their office that has their DHCP Computer and a Static printer connected to it and that unmanaged switch connects to my 9200 catalystSo my question what config woul...
