Resolved! Recovery logging from SWITCH
Hi,I would like to know If is it possible recovery some logging when a switch was restarted ?I don´t have syslog server.Thanks a lotRegards,Danilo
Hi,I would like to know If is it possible recovery some logging when a switch was restarted ?I don´t have syslog server.Thanks a lotRegards,Danilo
I'd like to move our AP connection to 1GB, we don't have any POE GB switches in location, I used a Power Injector to supply power to the APs, however when I put this in the mix the AP continuously restarts and is not able to see the controller? WLC 5...
Hi everyone, We have a lot of access points, which cannot backup configs to TFTP, if I specify $t environment variable in filename string. These settings result in failure: archive path tftp://172.16.0.10/$h$t write-memory N0010# wr Building co...
I have a stack of 3. When they came up, the following occurred: Switch/Stack Mac Address : 28c7.ce3b.e480 - Local Mac AddressMac persistency wait time: Indefinite H/W CurrentSwitch# Role Mac Address ...
We have some money to upgrade a 3750 L3 Switch we use as our distribution switch (VLAN routing). We need to move up to 10Gbs access ports to accommodate our VM environment. I know there has been much discussion about 6500 chassis vs. Nexus. It looks ...
Hello support group,I am trying to troubleshoot the follwing error on our Nexs5K and 7K devices. Error on nexus5K:2013 Oct 3 08:38:11.093 CPTORNDIS5B002 %FWM-2-STM_LIMIT_REACHED: Unicast station table dynamic capacity reached (limit 13800) - creatin...
Hi,We have setup a pair of Nexus 5596 L3 switches with 2 x 10Gbps LACP links between them to act as the vpc peer link. We also have another 2 x 10Gbps LACP links between the 5596 switches to carry non VPC VLANs, this is required to provide EIGRP rout...
I have multiple nexus 2Ks connected to two N7Ks with my servers connecting to multiple N2Ks accordingly with dual NIC failover capability.What happens, or what state do the N2K interfaces go into if one of my N7K's looses power given the N2K is effec...
Greetings. I'm swapping out 3750Gs with LACP etherchannels configured with src-dst-ip load balancing. These new nexus port-channels will have VoIP and Data, what is the best load-balancing option to use with the new setup? I will be using two 10G int...
Hi All,I'm currently designing vPC for a Nexus 9396PX deployment and I want to know if need to configure a separate parallel trunk link for L3 peering and non-vPC VLAN traffic.I have read a number of design guides and articles that recommend configur...
I have taken over management of a small network with a Nexus 7010 as the core router and I am new to the NX-OS world. I am trying to add an allowed vlan onto an interface but when I go into the interface to add a "switchport trunk allowed vlan" I don...
Hi, Will their be a service interruption during software upgrade to a switch? How long? thanks regards, AL
I have a Nexus 9K running that will not display the CDP information it receives from other Cisco devices properly. All of the devices end up showing up like below.1. The IP address is wrong. That is not the real IP address or even one in this netwo...
Hi all, I have not studied into STP yet. But in packet tracer, this is what I observed- Switch 1 (fa0/1) -- trunk -- (fa0/1) Switch 2- Created VTP and set both switches in the same domain, password and server mode.------------ On switch 1, i created ...
Hi ,I have Cisco 3650 switch which configured as stack ,after uploading new IOS to the flash ,I issue the following commandsoftware install file flash:cat3k_caa-universalk9.SPA.03.06.02a.E.152-2a.E2.bin on-reboot But I recieve the following errors : ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-09-2024 11:22 AM | ||
10-08-2024 08:34 PM | ||
10-08-2024 12:54 PM | ||
10-08-2024 01:38 AM | ||
10-01-2024 04:28 AM |
User | Count |
---|---|
8 | |
8 | |
6 | |
6 | |
4 |