Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! NX7000 - MTU Size

Hello, I configured 4 port channels with mtu size 9000. The VM engineers requested me to configre the same mtu size on the vlans assiged to those 4 port channels. I wasn't sure if I needed to configure the MTUs on the VLANs since I already configured...

Resolved! Hi all, need advice on OSPF and private vlans

Hi all.I have a project to complete and need some help on the possible solution I can use.Basically we have ospf area 0 and the users in question are in ospf area 7 and is a stub.I need to route the traffic from these users out through area 0 through...

Ableton34 by • Level 1
  • 3529 Views
  • 32 replies
  • 0 Helpful votes

Nexus online rack rental

Does anyone know of a company that is offering online rack rental for Nexus 7k, 5k or 2k?  We'd like to try out some changes without affecting our production data center without having to buy another whole set of Nexus switches just for a test lab.

ewood2624 by • Level 5
  • 3627 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Nexus online rack

Hello all,Does anybody know a place where I can rent Nexus 7000 equipment online? I wish to test some configuration changes but do not have a lab environment available. Renting a lab environment is much cheaper than building my own.I've looked at INE...

mvknl by • Level 1
  • 1614 Views
  • 3 replies
  • 0 Helpful votes

Resolved! C6500 Sup720 - Software CoPP

Hi,On C6500 Sup720, multicalst and broadcast traffic can't be handled by hardware CoPP, only software CoPP. Is it a real use to make CoPP filtering in this case, as software CoPP implies RP analysis?Beside that, I noticed that even making CoPP filter...

Network device A, Subnet

Hello Guys I have simple doubt. Please try to guide me. Its with respect to Network Device A? 1. With a network wide mask of 255.255.255.128, each interface does not require an IP address. 2. With a network wide mask of 255.255.255.0, it must be a La...

Catalyst 3850 Stack - 10G Modules

I have installed a (3) switch stack of Catalyst 3850 switches. I installed a 10G module in the 1st switch (the master) configured it and plugged it into the network and all works fine. Now I would like to add a second 10 Gigabit Ethernet connection t...

sm-es2-24 Gi0/25 Disconnecting

I have a sm-es2-24 in a 2911.  I am getting the following in syslog:%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/25, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/25, changed state to down%LIN...

cisco 881 password

Hi All,I set up enable password as well as telnet password on cisco 881-k9.with the same password :kadd2013no username confuguredwhen i saved the config , i was unable to login again using the same password i configured

okoroji80 by • Level 1
  • 697 Views
  • 2 replies
  • 0 Helpful votes

N5596UP & CAT6509E

hi, Cisco Experts:I am not a network expert, so I need advices:Example:Customer has X 2 N5596, X 2 N2224TP and X 2 CAT6509E & others like UCS 5108 Chassis, etc.Q1.Customer has X 2 10G Ethernet Uplinks from N5596-A to CAT6509E-A.Customer has X 2 10G E...

K P SIM by • Level 1
  • 853 Views
  • 4 replies
  • 0 Helpful votes
View All
Review Cisco Networking for a $25 gift card