Hi, It seems when I manually do a write mem, the crypto key is sent to the SCP server. When the archive is activated automatically with the time-period config, the switch doesn't send the crypto key. Is this by design?Thank you, Pat
Hi, It seems when I manually do a write mem, the crypto key is sent to the SCP server. When the archive is activated automatically with the time-period config, the switch doesn't send the crypto key. Is this by design?Thank you, Pat
I know this is not a 3com support forum, but am hoping that the Cisco GuRu's are watching. I teach the Cisco Network Academy. Our IT Staff recently upgraded the network infrastructure and changed our switches to 3com 4800g's (about 2 years ago).I w...
I'm relativey new to Cisco products, but not networking itself.I have two devices, as laid out below: Internet ^ |Cisco ASA 8.2 <---> Cisco 2811The inside interface of the ASA is 192.168.0.5. I have a cable connected to the 2811, and...
Hi,When on our 3750 Core Stack we get the following when pinging a device on a vlan.any ideas?Sending 500, 100-byte ICMP Echos to 172.30.32.161, timeout is 2 seconds:!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!...
Hi, We are seeing output drops on a C3560 switchport, this port does not have QoS enabled -- application does not need special qos treatment, as long as packets are not droppd, so I suppose all traffic will share the same queue? then how should I rea...
Okay, I am stepping in some completely unfamiliar territory that I need advise on. About a year ago, the company I work for added a new DR site. This site is connected by a 2 1gigabit connections. We had a lot of trouble with performance, and we had ...
We're trying to configure our Cisco 4507 (Supervisor Engine IV) to allow a new Dell server with a pair of Broadcom 5708 GigE NIC's to aggregate its NIC's to give us a 2gbps link to the switch.So far we seem to have got the team and LACP up and enable...
hi all,i have a cisco 3560x poe. ny currnet version is 12.2(58)SE2.the cpu process is aboute 30% average.my problem is- ping to the switch itself show me 12ms which is high latency.*note- data between two hosts no this has no latency.i realize the pa...
Im having problems changing a connection between a Cisco3560 and Cisco IBM Blade switch 3012 actually the configuration is access in Cisco 3560 and trunk int Cisco 3012 when i change the connection to trunk i lose conecctivity to the servers connecte...
Hello everyone, I wonder if anyone can answer this question:Since configuring HSRP for some of our networks, we’ve been having an occasional unicast flooding issue. The issue is documented on the Cisco site and in our case seems to be due to the asym...
Hello,We recently purchased two 3750-X 48-port switches. We are in the process of connecting the Data Stack and StackPower cables. The question we have is what is the recommended Data Stack and PowerStack cable configuration if you only have two sw...
We have a working MS-NLB cluster (I don't like MS-NLB but it wasn't my choice) which uses multicast with igmp. In reading on how to set this up I came across the fact that unless static mac address entries for the multicast mac address are added to t...
hi all,i've got a 1941 router that keeps on rebooting by itself every minute. currently, there's no power issue. i've detected the show version returned a bus error. can someone advise if this is an IOS bug?ROUTER uptime is 1 minuteSystem returned to...
Hey everyone,I'm working on setting up a template configuration for the Cisco ASA 5505 device that we'll use to configure more routers for various client needs. One of the requirements requested of me is the following:Internal hosts assigned a DHCP a...
I am new to the Nexus range and have a couple of questions to ask.1) If a NX2k is dual-homed to a pair of NX5Ks, which are joined by a vPC, which NX5K is the 'parent', and can you specify this?2) When connecting servers to the NX2Ks, what is the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-29-2024 10:44 PM | ||
08-28-2024 02:25 AM | ||
08-20-2024 09:12 AM | ||
08-06-2024 12:40 PM | ||
08-05-2024 10:24 PM |
User | Count |
---|---|
6 | |
5 | |
5 | |
5 | |
4 |