Hi Guys,Although Cisco CAT NAT support matrix shows that all 6500s running IOS support NAT. Can someone please confirm if I can do both NAT INSIDE/OUTSIDE statement on a single SVI.Regards,Deepak Arora
Hi Guys,Although Cisco CAT NAT support matrix shows that all 6500s running IOS support NAT. Can someone please confirm if I can do both NAT INSIDE/OUTSIDE statement on a single SVI.Regards,Deepak Arora
Good Morning All,I am currently working on configuring a new Point to Point connection (L3) between multiple sites. Site A and B are able to communicate, but I cannot get communication to site C working. The sites are setup as follows: Site A:1811 Ro...
Hello, excuseme for my english, writing from Venezuela.I am about to update The network for an International Airport. They have 450 users between Work stations, printers and VoIP Phones, 10 servers just 3 of them are critical. In a clones future They...
I have a c2969-48PST-L switch running IOS Version 12.2(55) SE. The switch is configured for 802.1x authentication. The radius server is a Cisco ACS 5.2. We are using PEAP and allowing EAP-TLS and EAP-MS-CHAPv2. Windows 7 PCs (HP Elitebooks) are using...
Hi there,We are getting some packet drops on our some 2960 switchs. sh int f0/27 | inc drops|bitsInput queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 102975 minute input rate 0 bits/sec, 0 packets/sec5 minute output ...
Hi everyone,Having some issues with load balancing two webservers using two CSS11501 content service switches (VIP/interface redundancy, Active/Backup, and Active Session Redundancy setup). I've set up both CSSs to load balance the web servers behin...
can we configure new switch without console cable.does switch have default ip and telnet enabled by default.
We have a 6500 Switch with 3 interfaces. One is out to the internet and is configured with NAT outside, one is to a local subnet and configured as NAT INSIDE (subnet A) . The Third is another local subnet (Sbunet B) and its interface has no NAT con...
I have two Cisco 4506's running cat4500-ipbase-mz.122-50.SG3.bin. Periodically, when attaching a new workstation to these switches the Mac Address of the device disappears off the port when the device is connected or the port is configured. The only ...
Hi everyoneI have recently purchased a Cisco 1800 series router and completed its cable connection using a brand new console cable and RS-232 card with two D-Sub 9 pin connectors. The router boots fine and the card is functioning properly but when I ...
I have a IP SLA being tracking a primary interface of a remote 2951 router. When the the pings to 4.2.2.2 from the primary interface fail - it sends a UP->Down to the syslog buffer and then it triggers the Event Manager script and the backup interfac...
Dear,I'm looking for technical document/datasheet for this Service Module SM-2GE-SFP-CU.If anyone know, please share with me.Thank you.
Hi i cinfigure the extended vlan and i know that these vlan is support when vtp is disable it means that vtp mode is transparent but my problem is if i change my vtp mode to client or server what happens to these extended vlan? Thanks friendSent from...
Hi allI have a question about the upgrade and install of IOS on newer cisco devices, Do we just have to run a licence install command ?if we want a newer version of IOS, I gather this is where we install the whole IOS not jsut licence it ?cheersCarl
Hai,I had setup a lan infrastructure with 5 3750 stack swithes. In these 3 of them are in one stack which is acting as access switch, 2 of them in another stack which is as core switch where all the SVI is configured. Now, when i t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-18-2024 06:41 AM | ||
07-13-2024 07:22 AM | ||
07-10-2024 04:41 AM | ||
07-09-2024 08:16 AM | ||
07-05-2024 06:35 AM |
User | Count |
---|---|
9 | |
8 | |
7 | |
5 | |
4 |