Hi all, Currently, Catalyst 1000 Series with version 15.2(7)E not support Flexlink function, but does it support Flexlink+?I've try to add Flexlink+ command on this model not success, the error displayMain port:interface GigabitEthernet1/0/1switchpor...
Hito enable Wake on LAN on 802.1x enabled ports the settingaccess-session control-direction both | inmust be used. From the descriptions it seems to be clear that the option in must be used, so that the switch can forward the magic packet to the devi...
There are 5 C9200 switches operating as a stack running IOSXE Version 16.9.3:- when making any configuration changes and type write memory command the stack shows the below log and then reboots with no any configuration change. Log: 001479: Jan 15 ...
I am trying to create a new fiber extension off of my 6880 X LE catalysts but the fex is stuck at "Registration" and the logs show: %FEXMGR-SW1-3-FEXMGR_MAX_VSLOT_ALLOC: No VSLOTs are left for new module to allocate. Enable Temp VSLOT to allow 'renum...
#Help I have recently upgraded our cisco 4507 switches from IOS "Cisco IOS XE Release 3.8.6E". to " Cisco IOS XE Release 3.11.6E". After upgrade Avaya 4625 and Avaya 9600 series phones stoped reaching TFTP and utility servers. There is no config ...
Hello,I want to upgrade 6880-x-le VSS switches from 152-1.SY4 to 155-1.SY8. My plan is to upload the new software to both switches and use the "reload" command.there is one thing that I am not sure of and that is the ROMMON. The current version is ...
Hi Guy's,I've just start my CCNA, and i have a question, why when we have two switch's and more than a vlan in each switch, we need a physical link for each vlan (without using a trunk ) . Sorry if my question seems silly
Hi I would like to get help from you guys for deny traffic at same Vlan. (I am using 9300 switch no router or firewall connected ) I have some vlan 10, 20, 30 ,40 Vlan 10 172.16.103.0/16 Vlan 20 192.168.20.0/24 Vlan 30 192.16.30.0/24 Vlan 40 10.0.0.0...
Hi All, I'm trying to enable netflow on this switch but it doesn't work:- I upgraded the IOS-XE from 16.12.03 to 17.06.03: #sh version ROM: IOS-XE ROMMON BOOTLDR: Version 7.1.8 [RELEASE SOFTWARE] crashkernel=64M xxx uptime is 2 hours, 27 minute...
hello,I had a problem updating C6880x. The currently running version is 15.2(1)sy5. The update attempt versions are 15.5(1)sy4 and 15.2(1)sy8.After updating, the 16p10G module is not recognized. The update method is as follows.1. copy disk0:c6880x-ip...
I have a stack of 6 switches that on occasion the stack ring will split into 1 and 5. Running show switch gave me one member as ready and the others as removed. When I would try to console into one of the others, it was unresponsive or was in straggl...
Hi everyone, seeking some advice here.I have around a dozen POS machines and printers in total, with LAN cable connections and my idea is to connect them to my Cisco SG95-16 switch. Which I will then connect the switch to my TP link 4G router (MR 640...
Hi everyoneI'm trying to upload IOS into my Cisco 3650-48FS-S switch. Looks like it is bricked now :-(I tried to boot from USB but I'm getting this kind of message: switch: dir usbflash0:Directory of usbflash0:/4 -rw- 537489817 cat3k_caa-universalk9....
Hi There,I have moved into a new project. Here i have to work with the vast network technology. So i believe that cisco packet tracker will help me to get the hands on experience, but i don't have the required devices on the packet tracer. can anyone...
So... I am not a smart man but please bear with me as I have made a mistake.A 9300 was given to me for configuration but the password seemed to have been forgotten me not really reading too much missed the article where I could bypass the config and ...
