Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hican I ask what is difference bewteen hotstandby and coldstandby in supervisor module 1   Standby Supervisor  RPR                 Standby cold 2   Active Supervisor   RPR                 Active Thanks

Hi All,I would like to know if there is any IOS currently avaialble for Cisco 2960 switch (WS-C2960-24TT-L) which will support maximum VLAN's of 1005 (or more than 255). Currently the switch supports 255 VLAN's. Wanted to know this limit is controlle...

arun kumar by Level 1
  • 18129 Views
  • 11 replies
  • 0 Helpful votes

As anyone experienced this problem:Im running POE for Cisco 504G phones with a PC attached to the LAN switch port on the phone.  DHCP is being served through a Cisco 1800 series router.It seems that the interface will shutdown and come right back on ...

On a layer 2 Cisco 2960, the management vlan is vlan 1. I have a couple of more vlans configured on the switch. In particular, vlan 8 is configured on two ports. From the CLI, I can ping the vlan 8 IP of a device connected to port fa0/8. After I see ...

Resolved! 3750G interfaces

HiI have a quick question, i have to deploy a 3750G switch to one of our sites and the interfaces are reading as if the switch was in a stack previously.when i go to sh run all the interfaces come up as 2/0/1 - 2/0/24.This switch will not be in a sta...

i created i new vlan 100 with ip address 172.16.10.1 255.255.255.0 for a new server range.current vlan i have arevlan20192.168.20.1 255.255.255.0vlan30192.168.30.1 255.255.255.0vlan40192.168.40.1 255.255.255.0i m using cisco 3560.ip routing is enable...

yeow_km by Level 1
  • 1368 Views
  • 11 replies
  • 0 Helpful votes

Hello all, it has been a while since I have dealt with Cisco so please bare with me.  I am looking at getting two 2960S 24 port switches, and I am wondering it talks about being able to have 2 x 10 GB fiber uplink ports.  Now can I use those two fibe...

Dear all,Does anybody know if today (July2010) EIGRP is able to "support and understand" delay metric on 10Gigabit uplinks differentiating them from Gigabit ?This would be very useful since finally we'll be able to avoid the manual fine-tuning on eac...

oguarisco by Level 3
  • 690 Views
  • 1 replies
  • 0 Helpful votes

when ip sla operation starts, do you know how many ping(s) icmp-echo sends to the destination when using default settings. if more then one, what is considered succesful?using 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T9ThxCeyhun

ctaymez by Level 1
  • 680 Views
  • 1 replies
  • 0 Helpful votes

Hi,We currently have a 6500 running Hybrid CatOS/IOS.  We are thinking about purchasing a WS-X6748-GE-TX we are running CatOS version 8.1(3) and IOS 12.2(17d)SXB8.  I have seen on some Cisco pages that CatOS 8.1(3) can support this module and on one ...

crepetti2 by Level 1
  • 1546 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card