Switching

We need some new patch panels at my company. I am thinking about going with blank keystone patch panels (ex. http://www.amazon.com/StarTech-BLANKPATCH24-24port-Blank-Keystone/dp/B00066HS44/ref=sr_1_2?ie=UTF8&s=electronics&qid=1263479274&sr=1-2). The ...

Let me explain the topology a little.We have these 2 networks that consist of seperate medical device networks that communicate with each other via there own VLAN'd network.  (SIP phones and some Nursecall servers and switch)   each VLAN houses these...

HiLately we are getting a lot of excessive errors on ports where a AP is connectedsh int fa1/0/25 | i error|runt     669 runts, 0 giants, 0 throttles     669 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored     0 output errors, 0 collisions, 0 inte...

I am having a duplex mismatch on faste trunk uplink between a 2950 and 6500. The 2950 auto neg at full/100, the 6500 auto neg at half/100. I tried adding the command "duplex full" on the 6500 interface and drop connection. This is my interface config...

Nexus 5k-2148 Integration to 6509VSSHi experts am new to this Nexus family and planning to do new deployement as per attached setup.After going through the Nexus docs i have prepared the configuration of Nexus 5000.(No box available yet and its awai...

Hi,Need a liitle help ! (Neo stated)I have a 10meg Broadband conection and a 4 port Linksys Router which I am very happy with the performance. i.e I get on average between 400kps - to 1000kbps from most sites. when my PC is directly connected to the ...

Hi Guys,I have a fastethernet interface connecting to customer kit and both the connecting interfaces are hard coded to 100/full.We are seeing output drops in 4 digits in a day on both the interfaces.The interface is underutilised as its doing close ...

Hello,I have a 802.1q trunk between a 2960 and 3750, VLAN 1 is being used for the trunk and management interface.  I'd liek to chaneg the Native vlan to 99 and the manage ment vlan to 100 on both, how can I do this?Thanks

Dear all,Do you know how to force GLBP to forward all traffic of a specific PC in a LAN to a specific gateway/router ? That means to override GLBP loadbalaningRegardsharis

Hi All,I'm not able to upgrade my 4506 switch.problem is: my earlier IOS is in inbuilt flash & now I have uploaded my new IOS to Flash0. we have changed the boot sequence to flash 0 & after restart it goes to ROMMON.Can u please let me know which com...

I have been looking around at our 6509 and noticed that the peak utilization on Module 3 was at 100%. I thought this may be a one off and returned later and found that the recorded time for the peak was the current time. It almost saying that it alwa...

I was reviewing the document :http://www.cisco.com/en/US/products/hw/switches/ps708/products_white_paper09186a008013159f.shtml#wp39211Regarding "Double-Encapsulated 802.1Q/Nested VLAN Attack", where the doument makes the recommendation to "clear the ...

Hi,     I have a 2611xm router as my main connection to the internet, with a T1. I would like connect a Cisco ASA 5505 that has 10 vpn lic included with it. I just can not figure out how to do it. any ideas or point me in the right direction. I am no...

Hello,We received an alert - PowerSupply_Fault_CiscoStack PWR-SWITCH [wscac2500w] is StateNotNormal. Indicates that the state of the power supply for this system is not NORMAL or SHUTDOWN."sh test" results are also attached. Can you please let me wha...