hi there, We have 3500 switches in my network and it is End of life and support also. now we are planning for chassis base layer 2 switches.we have 1000 ports network , so please suggest me which chassis are available with cisco
hi there, We have 3500 switches in my network and it is End of life and support also. now we are planning for chassis base layer 2 switches.we have 1000 ports network , so please suggest me which chassis are available with cisco
I've memory in a line card that has no label on it and I want to upgrade to 512MB. What command will alow me to see the RAM (256, 512, 1024MB) sitting on the board of a line card (not RP or SP)?Thanks!Matt
Hello all... I have a Cisco 2960 with 48 ports and 2 gigabit ports. I also have a Network Extreme Summit 200 with also 48 ports and 2 gigabit ports. My question is, how to cascade (maybe "bridge" could be the right word) thoses 2 switches. I got v...
I am getting 8 Mbps of Internet bandwidth from Service Provider throuth 4 e1 ports and I have Cisco 2821 Router with 4 E1 ports and built-in 2 ports giga bit Ethernet. I want that all my bandwidth (8 Mbps) should terminate on my one gigabit Ethernet ...
Hi all, just a quick question on ospf,When people say ospf routers know about the whole topology ofthe network, what does this mean? I would of thought that they would only know about the neighbouring routers?also am i right in saying ospf does not h...
Can someone supply a good example of CatOS C2948 config for QoS for voice?I've been unsuccessful at finding a good config guide on CCO.Thanks!
Hi,I've setup a 9 port stack of 3750s (config attached). Switches 2 to 9 are PoE switches that will be used to connect initialy to Mitel VOIP phones and then to PCs (The VOIP phones have a 3 port switch).I have plugged my laptop into the stack and se...
I am having issues configuring PVLAN using just trunks.Here's the secenario... two VLANs are being trunked from a 3560 to a 4503 (VLAN0030 and VLAN230). From the 4503 I have a port trunked on to an upstream 2811.I created a primary Vlan (VLAN0003) a...
Hi,We have two branches A and B connected by MPLS link.Now in A side we have total 4 ranges of IP:10.138.74.0/24 , 10.138.75.0/24 , 10.138.76.0/24 , 10.138.77.0/24.B side we have 3 ranges of IP .10.138.78.0/24 , 10.138.79.0/24 , 10.138.80.0/24.Now I ...
Hi all, Im in process of puttinga distribution layer into my network, whicj is routed to the core. My question is, should I put it all in the same area? or would I have different areas? what is the benefit of having these different areas?
Hi I have 1500 new 2960 switches, and want to upgrade image.Do it manually seems time consuming, so I looked at Ciscos website to do this with DHCP on bootup. It gets the IP, tftp and start to download the image, then it stops. I have tried to set t...
Hi, Internet Router | Firewall (inside ip 10.138.74.3) | Blue coat (10.138.74.5) |(VLAN -50) Access Switch |(trunk) |(trunk) core1 core2Now the problem is I am unble to access (ping) blue co...
HiI am new to CISCO. Please guide me how to do inter vLAN routing. Please tell me along with command
I want to make sure two routers have updated configs, automajically, but GLBP requires a gateway with a unique IP address. How do you auto-sync sso a 6500 or 3845 with GLBP enabled?
I need to prevent telnet access to a server connected to f0/0 interface from internet to achieve this I created the following access-list:deny tcp any x.x.x.x eq 23 permit ip any any I applied it to outbound direction on the f0/0 interface,....but di...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-24-2024 06:05 AM | ||
07-24-2024 01:13 AM | ||
07-22-2024 07:57 PM | ||
07-21-2024 01:36 AM |
User | Count |
---|---|
9 | |
8 | |
7 | |
5 | |
4 |