Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
hello,I need some assistance in how to get internet access accross my LAN. I have attached an image so you can see my system. I have internet access coming from the ourside and into my office and that is available via data port one on the bottom part...
Hello,My current Cisco Router 1812 configs. are as:1. My DSL connects to the FE0 port.2. My ports FE2-FE9 are automatically assigned IP addresses via the DHCP server from VLAN 1.What I want to do is stay on the same vlan but assign my printer which i...
Hi,I am little bit confused about this. My friend proposed the scenario like given below using a single switch.port 1 and 2 in the vlan 1port 3 and 4 in the vlan 2port 1: Machine APort 3: Machine Bport 2 (VLAN1 )--> Latency-Calculator/generator-Machi...
To create the trunk port, may i know what is purpose to create vlan database? Is it compulsory to create it?SwitchA# vlan databaseSwitchA(vlan)# vlan 5 name vlan5SwitchA(vlan)# exitSwitchA# configure terminalSwitchA(config)# interface fastethernet 0/...
Hi all i am using 2801 router with 14 Mbps internet. I am presently facing a very new problem the router hangs down after working for half an hour and no packets will be delivered and total internet service is down and the link successfully works whe...
Can anyone give me the link to the sdm for 3640 router. I have tried finding it even with a support contract account but I keep getting the run around on Cisco's website. Nothing directly to what I need.
I am facing a design problem can any one help on this regard.i will currently explain my current setup. we have two cicso 6509 with HSRP and two FWSM failover pairs in two switches. The cisco 6509 switches hoists all vlans for data centre and users n...
We have IPSec VPN from 106 remote offices to central site. 3 core routers running 2800 and remote sites are running cisco 1711.We have 3 tunnels to three different core routers on head office via three different ISP's.Remote sites are using one ISP f...
Which command is able to display interfaces' IP address, status and uptime?Thanks for help.
Resolved! mst instances
hi everybody!let say we have only two possible stp instances: ints1,inst2we have mapped v1 to inst1,v2 to inst2 where "v" stands for vlan.if a switch receives a frame for v1 but due to physical link failure inst1 no longer exists what will switch do ...
I bought an 1811 on ebay recently. The router came configured. The seller did not know the password, as it was programmed by a tech who no longer worked for him.Basically, I want to reset it to factory default,and load SDM, and use that to configure...
Hello,According to the following urlhttp://www.cisco.com/en/US/docs/ios/12_3t/12_3t14/feature/guide/gt_bgivt.html#wp1060626the command "ip verify unicast vrf vrf-name {deny | permit}" (uRPFv3?)was integrated into Cisco IOS Release 12.2(33)SXH.Howeve...
OK, this is a strange one. I must be missing something.I have 3 routers in a lab connected to the same switch with the ethernet interfaces for all 3 routers in the same vlan on the switch -- vlan 2.I placed all 3 routers in an HSRP group, with R! as ...
Hi,can someone explain me what are the differences between each logging type? Console logging Monitor logging Buffer logging Trap loggingI'm a bit confused, but I believe Console is the log's which we may see when connected via console, b...
I have a design question that I need help with. I have a flat network that is in the beginning stages of being split up into VLANs. Imagine two 6500's with networks on either end and both of these networks are in the native VLAN. In between the tw...
