Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hello Everyone Wondering if you have experienced this situación. I have a Nexus 7000 connected to a Bluecoat Proxy SG400 and for some reason it haven't been possible to setup the full 1gbps speed on the Nexus 7k side. When setting up speed and d...
Resolved! ctalys 6807
Hi,Does the below module from 6807 support single-mode SFP, and no which module supports it?If yes, is there any limitation?NAME: "Chassis 1 C6800-DFC Distributed Forwarding Card 4 EARL 1 sub-module of 7", DESCR: "Chassis 1 C6800-DFC Distributed Forw...
Resolved! C1121-4P Vlan not routing to internet.
Hello, Cannot find what is missing to allow devices attached to VLAN1 to access the internet. Laptop gets dhcp address, can ping 192.168.20.1 and interface gi0/0/1 which gets it address via dhcp. Laptop cannot ping 8.8.8.8. It has received an ip o...
1. Use Packet Tracer to put up the topology above. Connect the two multi–layer switches (MLS) with a Gigabit uplink2. Configure IP addresses where appropriate. Include the layer–2 (access) switch and the workstation. Use a private IP address block.3....
Resolved! QoS Marking
Quick rundown on my LAN: Access switches -> core -> internal routers -> firewalls -> DMZ -> router -> ISP We don't have any cisco phones or phones that support CDP so I'm not trusting any switchports. My plan was to set my trust boundary where the ac...
HelloAfter some advise for the best way to connect switches together over an encrypted link.We have two sites. Each site has a Catalyst 9300 three node stack.Between the sites are encryption devices - due to the implementation, these must be used.We...
Resolved! increase power budget
How to Increase power budget for copper GE POE port in IE-4010 16S12P from 80W to 360W
Resolved! refresh connection by cli
HI, My Product is C3750.It was disconnected . How to refresh via cli? BrgdsLiu Wei
I'm adding a new 9300 to an existing 9300 x 4 switch stack that are running a different version of IOS. After i boot the new switch and perform the software auto-upgrade enable command - is it certain that the new switch will downgrade its IOS to the...
Resolved! Multiswitch VLANs Using Trunking
Below is the network I have created using Packet Tracer (PT) v8.1.1.0022.I have configured (2) static trunk ports between the 2960 switches. VTP mode is set to transparent. My configurations are shown below. The example and configuration steps were t...
I have two C3750E switches connected to each other via EtherChannel ports SW Ver. 15.2(2)EI have configured 3 VLANs which all work and I have configured the out-of-bad mgmt ports (FastEthernet0) but I would also like to have in-band management so tha...
I want to enable the below policy using the aaa new-model but in the current subject switch model do not have the bold option after the aaa new-model. aaa new-modelaaa local authentication attempts max-fail 3aaa common-criteria policy xxxxxxxxxmin-le...
Hello, We recently acquired some WS-C2960S-48FPS-L switches. Almost every one of the switches shows this message on the console when connected via console cable. Is this benign?Switching, Catalyst 2000switch#mifs ifs_read 0 bytes
Hello Community,i'm having a Connectivity issue, I've noticed that mismatch duplex:ASA5525# sh int g0/0Interface GigabitEthernet0/0 "outside", is up, line protocol is upHardware is i82574L rev00, BW 1000 Mbps, DLY 10 usecAuto-Duplex(Half-duplex), Aut...
I'm in the process to configure cisco switch 3560 with a VoIP VLAN only and I want to specify a range of Mac addresses to allow access.
