Is it possible to configure Cisco 800 series router so that it does not include DHCP Option 51 (lease time) in its dhcp discover / request message? If yes, then what configuration is required?
Is it possible to configure Cisco 800 series router so that it does not include DHCP Option 51 (lease time) in its dhcp discover / request message? If yes, then what configuration is required?
Hi all, we have 2 routers at work, for the internet, the internal interfaces are using hsrp, my question is how do they route to these 2 routers on the outside if there are 2 seperate connections, will they just use bgp or something like that and hav...
Hi,What is the difference between FCS errors and alignment erros ? Both have a bad CRC ?Thanks,Navid
Hi,I try to set a RSPAN session but I didn't get what I expected.My configuration:First I set up a RSPAN VLAN (id 999) on the vtp server switch.vlan 999remote-span----------------------------------Source ports set up on a 3550 (12.1(22)EA8a)monitor ...
Does anyone know if there is an RFC for the VQP? I am thinking of creating a Windows VMPS server but need the details on how the protocol works.Thanks!!
Hi,What does it mean that ISL and 802.1Q allows the encapsulation of multiple trunks whitin a single trunk ?Thanks,Navid
Hello, A question : ISL does not support the processing of untagged frames, does it ?Thanks,Navid
Hi,This is my problem:-Ive a lmds 4 simetric connection attached to my cisco 1721 with wic 1enet. Downloading from internet and uploading to internet work properly uo tu 450 KB/s, but using a vpn 3des the upload is only up to 50 or 60 KBWhy?Best r...
Hi all, when setting up my 1200 series ap, do I put the ip address both on the fast ethernet interface and the BVI interface, or do I put no ip on the fast ethernet and just put one on the BVI and use the bridge-group command ?please help
I have an application that consumes most of the available WAN bandwidth during off-peak hours. Occasionally it runs on into peak hours and severely degrades WAN performance. The WAN router is SP managed, so I can not perform rate-limiting there.Traf...
Hello experts,The routing table of E3 shows the two routes to the 10.90.153.0/24 network,via 172.23.31.53 and 172.23.31.24.When I disconnect the link between THCC_1 and Test_1, the routing table onE3 updates to show just the one route via172.23.30.24...
hi guys, i have a very simple scenario but its not working, see i have a router wid fa0/0 connected to a switch, my pc is also connected to that switch. these are my configs for routerint fas0/0 ipv6 enable no shurthen in global config i typed ipv6...
by default debug statement seem to only go over the console port -- do you know if its possible and if so how, to get that debug data over a telnet (vty) console as well?
Hi, I'm having trouble understanding the documenation on prefix lists - examples like this don't make sense to me since you'll never see a network addr like 172.20.10.171/16... why wouldn't this be 172.20.0.0/16 since 172.20.0.0 is the only network a...
Hi.4 AP are installed in port POE of switch CE500. Using homing in APs, when notebook leaves a covering area of the AP1 and enters in the area of covering of the AP2 , the switch don't update arp table and the mac of notebooks appears in the 2 ports ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-13-2024 07:12 AM | ||
08-13-2024 06:43 AM | ||
08-06-2024 12:40 PM | ||
08-05-2024 10:24 PM | ||
08-04-2024 01:12 PM |
User | Count |
---|---|
8 | |
7 | |
5 | |
4 | |
3 |