Hi,i have a simple question.i want know if we can affect switchport to a several vlan.
Hi,i have a simple question.i want know if we can affect switchport to a several vlan.
Say you have a L3 switch. One of the ports is routed (no switchport), and another is a switchport. Is it possible for devices coming off both ports to be in the same subnet? Can the devices coming off the switchport use the routed port as their de...
Does this model support VLAN routing?
Hi,I have a cisco 801 router.it was having the ios 'c800-y6-mw.123-5d.bin'.I was trying to do a password recovery and now it is in boot# and not entering inside.when i gave the commandboot# bootAccessing flash:c800-y6-mw.123-5d.binboot flash: failed,...
I have Cisco 2611MX router, I am about to upgrade ios so I would like to 1. Default ios, latest released ios with there size.2. I also like to know Default ios, latest released ios of other router also.( Cisco 2691/2811 router, 3560/2960/3750 swit...
Hipls help me by forwarding the links relating(cisco notes)V-lan and Access-list.Thanking you
Between: 4-Port 10/100 Fast Ethernet Switch WIC4-Port 10/100 Fast Ethernet Switch WIC (spare)Best regards
hi guys plz help me in this,i have 3 routers connected to each other like this O------------O----------OR1 ISP R2i m using a tunnel over ipsec to allow routing via ospf between R1 and R2 everything goes fine, but when the tunnel goes...
Hi,I'm trying to get a Management Vlan running which isnt VLAN1 due to the secruity issues and best practise.I have programmed switch as shows:!ip subnet-zero!interface FastEthernet0/1 switchport access vlan 10!....!interface FastEthernet0/24 switchp...
hello folks i am new to cisco i have 14 cisco routers some 2500,2600,3600,switches,1900,2900,3500,i have read the setup for telnetting with the 2511 can telnet to most but not to all,i am using both asyn lines any reason why i cant connect to all the...
Hi guysI have a cisco 4503 core switch and about 5 edge switches 3560 , one for each floor in my office. I have configured a dhcp server with the respective number of scopes as number of vlans which is 6 in this case. Ive set the IP helper address an...
I have 2 Cisco 2950G-12-EI, S1&S2 connected with two uplink cable as the other one is redundant. S1/P11 connected to S2/P11S1/P12 connected to S2/P12(Blocking State)How I can enable the S2/P12 to forward state, so that if I have a host connected in S...
Hi again . now I was able to get from comm-server 2511 to 2610 when I canfigured the loopback0.. now I wan to getback to 2511 com-serv its says on the doc that I need to do Ctrl+shift 6, twice// I did but I am still on the R1 PROMTdo I need to config...
Need the following objectives:Need 1 WAP Cisco 1130 to have 2 SSID's and each one it's own separate VLAN. - Vlan 18 is going to for employess - Vlan 19 is going to be "public" it will only have access to InternetI have 1 vlan for internet which i...
Hi Does anyone have inroads to cisco to check if they have plans on releasing a new Supervisor Engine for their 4500 series. example support for more routes would be a great start!Tyrone
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-09-2024 11:22 AM | ||
10-08-2024 08:34 PM | ||
10-08-2024 12:54 PM | ||
10-08-2024 01:38 AM | ||
10-01-2024 04:28 AM |
User | Count |
---|---|
8 | |
7 | |
6 | |
4 | |
4 |