Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

HiI have just set a RSPAN vlan and some ports to monitor but dont seem to be receiving any IP traffic. I can see the MAC addresses of hosts im trying to monitor across the RSPAN vlan.Any ideas ?Cheersswitch with sniffer connectedSession 1---------Typ...

Hi all,First time i've posted a question here so forgive me if it's a stupid one..I'm costing up some 6506E chassis' for my company's new network design. And I'm running into some issues that has to do with the understanding the different types of I...

comms by Level 1
  • 461 Views
  • 2 replies
  • 0 Helpful votes

BGP

Bgp-p4s ,if Any One Tell Question No.53 And 93 Answes i want BGP p4s 53& 93 answers

Resolved! ip nbar port-map

I'm wondering what purpose of port mapping in nBAR, how and when it is used during packet inspection. Why port maches are needed when deep packet inspection is done anyway. For example, if I'm accessing web page with port 666 (http://www.example.org:...

I have attached my config file. I am tring to setup vpn to be used on remote pc and connect to router. I am not sure what I did wrong on the setup. Any and all help would be appreciated.This is the first step of many I have to embark on, I am tak...

Hello!i have this version of switch:Switch#sh verCisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)XU, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2000 by cisco Systems, Inc.Compiled Mon 03-Apr-00 1...

alsayed by Level 1
  • 2092 Views
  • 6 replies
  • 0 Helpful votes

Hi Experts,Just going through my new CCNp switching book, and i see a tip that says that support for ISL has ceased accross all Cisco Catalyst platforms.Would anyone like to confirm this?RegardsStephen

We have 6500 with IOS version "c6sup22-jsv-mz.121-26.E8.bin". 6500 has one 8-port GBIC blade and a few 48-port GE-TX blades.On GBIC port "switchport trunk encapsulation dot1q/isl" can be configured. But on GE-TX, there is no command opiton for that.H...

tunemore1 by Level 1
  • 553 Views
  • 3 replies
  • 0 Helpful votes

I am trying to hook up a Cisco 2950 Catalyst switch. I have run cat5e straight-through from the router to the switch. I toned and tested the cabling. It is working fine. However, when I plug it into the switch, the server can't see the network. ...

samreeves by Level 1
  • 570 Views
  • 4 replies
  • 0 Helpful votes

Hi,I am sending to ask about the ISR security bundles which is more expensive than the regualar software. So, If I want to implement mainly the firewall features plus NATing on my ISR router, I know that the regular router software can do it, but wha...

I've setup a 1721 on an adsl connection. Everything works ok except the local dhcp server. Its setup as per all the proper cisco documentation but for some reason it just will not serve addresses to client pc's.Ive ran a dhcp debug and tried an ipcon...

jdinsdale by Level 1
  • 1404 Views
  • 6 replies
  • 0 Helpful votes

I have three vlans on a 3750: 50, 51, and 52. I currently have ip routing enabled and all traffic is routing between the three vlans okay, but now I want to limit traffic to vlan 50 (use 50 as the management vlan and 51 and 52 for access vlans). do...

matt_heff by Level 1
  • 510 Views
  • 1 replies
  • 0 Helpful votes

Resolved! vlan

hi allFor example I want configure vlan 16 to 5-ports at a time in cisco 2950 if its possible give proper command.

Review Cisco Networking for a $25 gift card