Resolved! CATALYST9500 error
Hi All.I have a CATALYST 9500 switch.when the command "reload" is executed the switch reloads and goes into a endless loop and then shows the following error:error-adelphii2cwriteactAny idea how to solve it?Thanks!Danny.
Forum Posts
Hi Frineds,I am having issue with integration between Cisco and Hirschman switches. there is different pattern of cisco mrp domain-id which is FFFFFFFF-FFFF-FFFF-FFFF-FFFFFFFFFFF and in Hirschman 255.255.255.255.255.255.255.255.255.255.255.255.255.2...
The switch is not still booting to the exec mode ......it hangs as in the attached image. when i press enter or no ..it doesn't go further. Pls help
I have two 6800s that have layer 2 and 3 links between them. I want to configure HSRP for specific subnets only on the two routers located 10 miles from each other. I want the existing subnets not to participate in the HSRP Active/Passive redundancy....
Take the opportunity to reach out to our expert and discuss best practices regarding on how to troubleshoot a live network and identify the root cause easily. Learn more about Serviceability and how to provide full access to the administrator in ord...
In Stackwise Virtual Link on 3850 XS. We use 2 interface on both the Switches for configuring Stackwise Virtual Link and 1 interface for Dual Active Detection. Can Any 1 explain why 2 interface are configured in this stacking system?If we configure o...
I have 2 9300 switches that are OOB new without configurationSwitch one is:bootstrap 16.8.1r (FC4)IOSXE 16.06.04a Switch two is:bootstrap 16.12.2.rIOSXE 16.06.04a Switch one will power a Ieee PD class 4 device file, while switch two will not power th...
Resolved! HIGH CPU on 3560 L2
OUTSIDE-DIST#sh proc cpu | ex 0.0Core 0: CPU utilization for five seconds: 85%; one minute: 86%; five minutes: 88%Core 1: CPU utilization for five seconds: 83%; one minute: 93%; five minutes: 83%Core 2: CPU utilization for five seconds: 100%; one min...
Hello all.I am in trouble with WS-C3650-24TS-L and vrf forwarding Mgmt-vrf Issue.I couldn't find a solution and a reason for this behavior.Switch A is WS-C3650-24TS-L and the Switch B is WS-C2960X-48LPS-L.Switch A and B are connected to each other w...
My new Catalyst 2960L-24PS-LL Switch (15.2(6)E) fails to provide POE+ power to Linksys LAPAC2600C. The switch provides regular POE (15.4W) instead of POE+ (25W). The LAPAC2600C AP reports power source to 802.3af instead of the expected POE+ standard ...
Hi all,I have a strange behavior from WebUI. After updating a 2960L to 15.2.7E3 I have been unable to access the content of the switch web pges.The HTML folder is there, after learning that the .tar file is the right upgrade (initially updated to the...
Hi, in our network we have few hubs connected, some time if any end user connects two ports of hub with any tail Cisco switch ( in normal only one port from hub should be connected to Cisco switch) we see host MAC address flapping alerts like this.Oc...
Resolved! CISCO 2960X etherchannel with Checkpoint / Span blocking one member after software upgrade
Good evening, we are running a CISCO 2960X with an LACP etherchannel to a port bond on our Checkpoint with abouth 7 VLANs using the bond.This was running fine on 15.2(2)E4.In a short maintenance we rebooted the switch, knowing that it would upgrade t...
Hello,befor two days i did an upgrade to 9.16.09.06.SPA on two WS-C3850 Switches.I did it with "software install file <image-name>"Install process looks fine, but after reboot, both switches will not boot any more.The LED-Statis is:STAT = greenDUPLX ...
Hello,I have a strange problem in one segment of our network. We have a cisco 6509E router and some switches (3750, 2960 etc) connected into this 6509 (The 6509 is the centre of star and switches are edges). Sometimes (once per day), occurs long ping...
