Hello, We have a pair of NX7Ks and they are configured in a vPC. We have a requirement to connect the pair of the vPC peers(NX7K_01 and NX7K_02) to a Router using a L3 Port-Channel and use sub-interfaces on this port-channel.The doc below under the "...
Forum Posts
I have searched on here but can't find the exact answer i am looking for. I have a cisco 1760 router and a 2950 switch. The router has an ethernet wic card added so i have two ethernet connections available. I would like to connect the cable modem ga...
Hello community, Can anyone explain to me the bellow point : show hardware access-list resource utilization slot 1 ======= INSTANCE 0x0 ------------- ACL Hardware Resource Utilization (Mod 1) ----------------------------------...
I have configured 9300 switch with management on MGMT port. No IP defined on vlan or physical interfaces.I have configured snmp V3 and I am unable to monitor the switch using my NMS software. Is there any specific setting need to be defined to monito...
I would like to disable icmp redirects on C9300 running CAT9K IOSXE 16.12.4. We have a environment that uses static routes to reach its destinations. Security have advised to disable ICMP redirects on the host but the command no ip redirects doesnt...
Resolved! VACL
Dear All, Please advise on the below. Say in vlan 3 i have hosts 10.1.1.1 and 10.1.1.2. I have applied the vlan filter as below. According to the Cisco DOC for VACL, even if there is a deny for the host, it will still check the next sequence and if ...
Resolved! TRUNK Port : what is connected ?
Hello,I search the command to know what is connected on a TRUNK port (it could be also a ACCESS port).I need to know the IP address.(Catalyst 2960-X / 9200L / 9300)Regards,
What is the time difference of the arrival of a packet between a port and a mirror port?I am working with Catalyst 2960 Switch.Thank you
Resolved! C3650 Output queue drop(OQD) problem..
Hi.I ask for help with the C3650 Output drops issue.The G1/0/4 port of the switch is uplink and the bandwidth is set to 80Mbps.If you check the actual equipment, speed/duplex is connected at 100Mbps / Full.The output drops of the port rise very high ...
Resolved! Vtp Particular Vlan Replication
Team, I am about to install a setup with VTP Server and Client Architecture. There will be 1 core switch(VTP SERVER) and multiple access switch(VTP CLIENTS). There are 20 Vlan configured in core switch but in access switch only 5 is to be replicated...
I'm looking at a 6509 on a site where the client manages their own LAN but are having problems. I have found several interfaces to be in Up/Down status and one of them was incrementing significant Output errors with collisions nearly matching total p...
Hello,I was wondering if you can help with a configuration on a Nexus 7k regarding source static routing. I am trying to accomplish seperate static routes to the same destination, but different next hops depending on source. for instance:(Src: Vlan A...
Hello, My client try to transfer huge blocks of data using the file transfer protocol (FTP) but he found that this transfer take a lot of time to be done. To make sure that this problem came from my network, he did the same process (tranferring files...
Hello, We recently converted our CATOS 6509 with an MFSC2 to Native IOS, 122-18.SXF8, and I want to view specically the SP memory, but cannot find the command. We know the RP memory by a "sh ver", but need to see the SP memory. thanksjackyjoy
Customer requires read only login access. This read only account should be able to run all 'show' commands on a catalyst 3560 switch
| User | Count |
|---|---|
| 16 | |
| 9 | |
| 7 | |
| 5 | |
| 4 |
