Hello, Hope you are doing well,I did a project with your help, that consist of 6 companies with 6 different Vlans with 3 L3 switches. So when I am sending a packet from Vlan to another, the packet cant reach the other switch.My doctor told me to enab...
Forum Posts
Hi,I'm trying to use some combination of route-maps and / or ACLs to write a destination-based NAT policy that would essentially do the following: Take any source address of 10.x.x.x/8 and if it is going to (list of subnets) than NAT to (host IP) and...
Hi expert I would like to know if we can stack switch between difference model. Such as Cat 6500 with 4500, or Cat 9500 with 6500 etc
hi all,just wwondering as the normal commands arnt working to find the mtu size on a interface portwhats the command to find the mtu size for a specific interface portthanks,rob
Resolved! Connection Refused SSH WS-C2960S-48FPS-L
I'm very new to Cisco and this is my first configuring of one of their switches. No matter what I do I'm unable to ssh into this switch.Building configuration...Current configuration : 4458 bytes!version 12.2no service padservice timestamps debug da...
Resolved! Cisco 9300 QoS - CoS configuration
I'm hope to setup Cisco with QoS in L2 environment with VoIP traffic. The packets ingress the SW will be marked with DSCP values. The requirement says that if L2 QoS if necessary the L2 Ethernet switches should be used that can implement QoS measures...
hey, I have this exercice for the advanced network if someone can help me with it.We configured the adhoc wireless network in the figure below with nodes A, B, C, and X (accesspoint). The range of each node is illustrated with the circle around it. W...
Hi everyone,i have 3850 switch with boot issue , anyone familiar with log below ? ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ...
Dears, Can someone help how to configure netflow on Cisco Switch Cat4500IOS : Version 15.0(2)SGRommon : 12.2 KR
Resolved! 9200L high availability
Hi; I have 2 cisco 9200L switches and I cross connected them with Stack cables (1 to 2 - 2 to 1). Switch# Role Mac Address Priority Version State -------------------------------------------------------------------------------------*1 ...
Hello,I am running c800-universalk9-mz.SPA.157-3.M.bin on cat800 router and need help how to configure IP SLA.cause it seems like Ip Sla monitor command is not supported. Please help
Hi everyone, I have a question after many days of research....is there anyway I can find the maximum number of IPsec Tunnels and number of Firewall sessions on this router series? Regarding the IPsec Tunnels, the only info available is the scentence ...
Dears, I am having vulnerabilities issue with SSH weak algorithm.Can someone help how to change algorithm used by SSH on Cisco Switch Cat4500IOS : Version 15.0(2)SGRommon : 12.2
Hi,I want to factory reset my 3750 because we lost admin password. [ 3750 ios 12.2(25) SED1] I succed to arrive at the point : The system has been interrupted prior to initializing the flash file system to finish loading the operating system softw...
Hi All, I have a WS-C3850-48T with 16.3.5b and aaa common-criteria policy command is unavailablebut on other switches which runs on 15.5 have this please advise
