TelePresence and Video Infrastructure

Integration CUCM with MCU Cluster, TCS and TMS

Hi all, Do you have any guides, information and suggestions about integrating CUCM with MCU, TCS and TMS?To centralized IPT and Video Conference enviroment, i need to register MCU and TCS to CUCM v10.5.Also TMS should provision devices which are regi...

C90 codec

Hi, I have a public IP connected to C-90 at customer location and he want the VC with other four or five location with different public IP . My question is how many outbound public IP's can C-90 dial and put all four locations in conference with out ...

Resolved! IX5000 phonebook behaviour

HiI have what may seem a simple question, but I am unable to find confirmation anywhere.We have an IX5000 which receives a global phone-book from CUCM and I wonder if the following behaviour is correct. We select the phone-book and see a blank page w...

SX10 with problem when the source use NAT

I can´t use the telepresence when the origin use NAT.If it use a public IP as the source, the conection is closed normally.The question is: how can i use a NAT in the source? Thanks.

Resolved! SX10 T7.1 with Expressway MRA

Hi all, Does anyone know if it is possible to make an SX10 on the Internet work with Expressway MRA? The only options I get for provisioning are 'CUCM' and 'VCS'. If I select 'VCS' and enter the Expressway -E's address and I look in the log, I see th...

VCSE certificate

Will an expired certificate on a VCSE cause it to go unresponsive?

DX80 - Sluggish Interface / Directory

I have a dozen DX80's deployed and am finding that the interface when your try to dial or directory look-ups gets sluggish after the unit has been on for a while. Starting to document how much time it takes now. I have checked memory, app utilizatio...

L2 multicast, where to place igmp querier

Hi,question to igmp and querier in a L2 network. Assuming snooping is enabled on all switches.Querier sends query to 224.0.0.1 which is forwarded out all ports by switches by default.Receiver answers with host membership report to the group beeing re...

Resolved! Conductor and TP : license

hello, I will not understand how the resources of licenses in status page of conductor.In a test, I have a TP with 5 SL, which should support 10 Calls : main-> 720p30->Content720p5, right?I have one conference template that specific:Participant quali...

Can't dial number with dash in SX10

All,I have setup SX10 7.3.1 with CUCM 9.1.2. When I pull the AD information and click the phone number to dial, the SX10 can't make call with number like +1-123-4567890@xxx.com. When I manually punch in +1234567890, it works just fine. Any idea how I...

SX80 -- 3rd Camera always on 3rd monitor

Hi all,I have an SX80 which has a ST60 along with another Precision 60 camera. I also have 3 monitor outputs hooked to this system. What I want to do, is make it so that the 3rd monitor *always* shows the 3rd camera only, in full screen. This is s...

Cisco SX80 installation

HelloI was installing SX80 codec and camera precision 60 there was some confusion.On SX80 codec there are three lan ports first one is for network lan port connectivity.second lan port is showing in diagram is connected to camera and provided power a...

Using wildcard certificates on Cisco VCS

A quick question, are you able to use Wildcard certificates on Cisco VCS?A customer has purchased a domain wildcard certificate from GoDaddy, and has asked if we can use this certificate for Cisco VCS.I have looked through all the documentationa and ...

How to enable SRTP on Cisco sx20

Hi, Does anyone know how to turn on SRTP on Cisco sx20? It seems it's supported from spec but I don't know how to get it turned on and use it...Thanks!

sx-20 missing release key

i just turn on the system and get the massage missing release key, i don't have access to the setting' don't have a ping to the system.i have the key.How to release the system?

TelePresence and Video Infrastructure

Forum Posts

Integration CUCM with MCU Cluster, TCS and TMS

C90 codec

Resolved! IX5000 phonebook behaviour

SX10 with problem when the source use NAT

Resolved! SX10 T7.1 with Expressway MRA

VCSE certificate

DX80 - Sluggish Interface / Directory

L2 multicast, where to place igmp querier

Resolved! Conductor and TP : license

Can't dial number with dash in SX10

SX80 -- 3rd Camera always on 3rd monitor

Cisco SX80 installation

Using wildcard certificates on Cisco VCS

How to enable SRTP on Cisco sx20

sx-20 missing release key

Meet and congratulate the February 2023 Spotlight Awardees!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

Cisco Codec Pro Question

Recording p2p calls on Codec pro

CS-Codec-Plus V01 # TCC7-25 compatibility with Polycom RealConnect

CMS 3.3 Webbridge LDAP user login issues

FN - 72497 & 72517 related to Cisco Room Navigator

Expressway zone not responding- inbound TLS negotiation Error

UNLICENSED STATUS ON CMS WITH CMM

Cisco Webex MS Teams video calling (VIMT)

Quad Camera Power Supply part number?

Audio distortion from a cisco webex codec pro