Resolved! VCS 8.1 on Fusion
Hi,Anybody been able to install 8.1 on Fusion? I get error "System error: (std::exception)" when trying. Or is only supported on ESXi ?Thanks
Hi,Anybody been able to install 8.1 on Fusion? I get error "System error: (std::exception)" when trying. Or is only supported on ESXi ?Thanks
Hello All,I am trying to configure D9854 Advance receiver and getting the following error. Please suggest the solution.Error message.Boot 5.00 copying safe app codeChecking secondaryother erro.Component ‘wdog’ failed to init in phase 3
Hello everybody,from where does the Smart Scheduler gets the time zone? I realized that I configured under "TMS > Administrative tools > User Administration > Users" "(UTC+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna" as time zone but when...
If I'm calling the Cisco TCS directly from our EX90 the video resolution is only 576p but the call setup is with 6Mb/s.We're using the Cisco TCS SMB solution that we've ordered with BE6k.What could be the issues that we got no HD resolution for the r...
Hi, all My PHD-1080p12x has some wrong, So I want to resolve for your help.The issue is that PHD-1080p12x don't work.Green lamp is on, so I think that connected is not wrong.But xstatus check of the camera status.xstatus Camera 1 Connected: FalseCode...
dear all - i would like to configure the c40 codec & test it.Can anyone send me the cli template which can be pushed in to c40 to work? scenarion - c40 directly connected to router to reach internet.no vcs in this scenario. router does the nat privat...
dear all - i would like to configure the c40 codec & test it.Can anyone send me the cli template which can be pushed in to c40 to work? scenarion - c40 directly connected to router to reach internet.no vcs in this scenario. router does the nat privat...
I've encountered a problem today with a couple of C20s and duplexing errors.As we run fibre everywhere, auto-duplexing is not an option so run everything at 100/full duplex and all our endpoints have this hard set.Today we've had a couple of C20s boo...
Sometimes my telepresence management suite send the message "there is a connection problem between tms and the system" and all the call conference and videoconference don't work.I try to ping all the component of my architecture and don't loss any pi...
I was wondering if it was possible to connect a dx650 without using call manager and just connect it to the VCS and TMS. I only want to use the device to call using H323.Thanks
Hi Guys,I am just geeting my head around this Vide stuff, so please tale it easy on me I was looking at a call log fro a call between a VC to VC. And I saw these lines below. Can someone please clarify how TMS is involved in this call flow. I can see...
Hi FolksWe have TMS and VCS (Control and expressway) in our enviornment.We also have many C series devices which are registered with different VCS.We had 4 VCS and the video devices registered with these VCS having different username and password.The...
Does anyone know how to clear the counters (Total calls and registrations) in the VCS other than a restart????Chet Cronin
If possible may I get information on the procedure to customize and update the VCS banner. Ofcourse it will state "powered by CISCO" thank you.Chet Cronin
Hi Guys,I have vcs ver 7.x with h323 endpoints registered. I also have cucm ver 8.6 with jabber registered to it. I am trying to setup an integration between VCS end CUCM. I have configured everything..Setup cucm as a neighbour, setup transforms and ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-09-2025 12:11 AM | ||
02-05-2025 11:17 AM | ||
01-29-2025 08:03 AM | ||
01-27-2025 11:28 AM | ||
01-21-2025 03:17 AM |
User | Count |
---|---|
1 | |
1 | |
1 | |
1 |