I have an MX300 running TC6.1.1 registered to CUCM 9.1.1a. The xstatus //ntp shows it pointing to the correct NTP server in the CUCM Date/Time Group. The customer says the time displayed on the touchpanel is off by 1 hour 45 minutes.Thoughts?
The Email confirmation that comes from TMSXE 3.1.2 has a section that has the following, "An agenda has not been added for this meeting". It is unclear how one would add an agenda. Can someone point me to the correct doc?thx,rf
Hello, I'd like to know if there is a document somewhere stating which systems could be registered with TMS 13.2.1 and TMS 14, because we were thinking of upgrading the TMS or not, also we had a bunch of systems, old ones too which we're not that sur...
About 1/6 manual phonebook entries are not showing in a movi search. They haven't changed for over a week. I've checked access control, all phone books are available to all users. I can't see anything else different about the ones that aren't populat...
Hi, I have the following problem. A redirected call comes from CUCM to H323 VGW and leave Pots Dialpeer BRI S0 ISDN as a Q931 Setup Message. But redirected number is not seeing in Outgoing Q931 Setup, only the Calling and Called Party Number. CUCM...
Hi,Can anyone let us know how to configure dual display on these codecs?We have the dual display licence installed but we cannot get far end camera on on monitor and near end on the other or presentation on one and far on the otherAll 3 PIP (far, nea...
Hi !We have mcu5310 server and some terminals (e20 , c20) in different networks and behind NAT. How we can make direct calls via terminals without creating conferences in mcu5310 ? And is way to call to pre-configured participans from mcu5310 if part...
Hello, I'm in the process of clustering two of our content servers. I have prepared most of the stuff needed but when i were about to setup the SQL instance on our SQL server we noticed that our server isn't running 3 Ghz processors as the clustering...
I have a c40 and cannot get the second camera to control via the daisy chain. I have tried several cable connetions but cannot get the camera to work. I looked at the xstatus and camera 2 always comes back as false. I have swapped the camera position...
Hellow,What is the difference bewteen the following license options on the SX20? What are their limitations and capabilities?LIC-SX20-PR vs LIC-SX20-HDThis thread did not answer my question: https://supportforums.cisco.com/thread/2157275Does the SX...
Hello,I have installed a videoconferencing infrastructure integrated with Cisco Voice infrastructure. Video infratructure has MCU4500, Cisco TCS, VCS, VC endpoints and Voice infrustructure has CUCM, Contact Center application and ip phones. I created...
I am buying a C40 and some 8945s. I want video endpoints on the outside to be able to call in to our video endpoints registered to Call Manager.I am being told that I need both a VCS Expressway and Control.I thought you built a trunk from Expressway...
I use TMS to schedule recurring meetings that are also recorded. As an example I have one titled "1st Hour Spanish". The issue is in Show-n-Share I will have 100 recordings titled "1st Hour Spanish". What I would like to do is have it automaticall...
Hi. I have a strange issue with a complaining TMS that tells me that a CTS-1300-47 has not been registred on the CUCM. Strange enough, that this device was added long time ago and works well, so I am a bit confused what this could be. - TMS (14.3) co...
The parameters "Limit" and "Offset" in the xcommand phonebook search command do not work anymore in TC6.3.0. The endpoint ignores their values. I attached two log files that show the different behavior between TC6.2.1 (and earlier) and TC6.3.0
