I cannot get the Operator conference in TMS to work. Each time I try, I get the window to select the endpoint to put into the conference, but I get a message that Start time cannot be after end time. Any suggestions? TMS is 13.1.1. ...
I cannot get the Operator conference in TMS to work. Each time I try, I get the window to select the endpoint to put into the conference, but I get a message that Start time cannot be after end time. Any suggestions? TMS is 13.1.1. ...
Hello,MCU : Codian MSE 8510 Blade (configured in HD mode)Software version : 4.2(1.46)Build: 6.17(1.46)The bridge has been rebooted unexpectedly this morning and we are actually investigating this problem. I would appreciate if you can help me and pro...
Issue1:We recently upgraded to TMS-PE with TMS 13.2.1We are trying to monitor the users provisioned from Systems > Provisioning > Devices.We do see the users provisioned and the corresponding times. But most of the entries are seen with empty Video A...
Hello.I've seen that there is a new video collaboration way with cloud services through Cisco Webex Telepresence service, but I don't see if it interacts with Webex Meetings.Can I join to a Webex Telepresence session from a Webex Meeting session?Rega...
Hello,Is it possible to use show & debug for diagnosing any GTW problem?If yes,How to proceed?
HiWe have a client that wants to relocate a Profile 55 single screen unit that is currently on wheels/casters. The client he would like to wall mount it in the new venue. I know you can order a wall/floor standing or one on wheels with the profile ...
Hi,I have a scenario where a single instance of TMS is managing a number of endpoints, MCU's and ISDN Gateway's across two different geographical locations.The WAN link between the locations is not good enough to support all IP calls yet, so i am usi...
Hi There,I was wondering if anyone knows a way to turn off dual streaming (H.239) on an SX20? We want to be able to use the "Laptop" button on the remote or the "Present" button on the Touch 8 to just change to the PC input but not initiate dual stre...
Case 1: VCS-C<==[Firewall]==>VCS-C<====>InternetCase 2: VCS-C<==[Firewall]==>VCS-E<====>InternetIn both cases , there are option keys: Encryption, Interwork, Traversal, Non-Traversal.I have 3 questions and I hope someone please to answer them:Q1. Whi...
Hello. I wanted to add the CUCM (9.1) to our TMS (13.2.2) according to the steps in the TMS docu for CTS and CM integration. CUCM shows up after the "Add system" task together with the registered CTS-1300 (below the CUCM entry).. The CUCM appears in ...
TMS allows for Automatic MCU failover:- if conference start fails- if conference start fails or MCU Polling failsNot much documentation is found on this.For the part 'MCU Polling fails'. Does this works for SIP?What is the requirement for this failov...
Is there a way to automacitally input the date in a recording's name using the recording aliases?
We are having an issue with the meetings button not showing on the touch 12 for a TX9200 registered to CUCM. Currently we only see three buttons at the bottom of the touch screen: call, presentation and more. We meet the compatability requirements th...
We just installed a trial of the TMSXE service. It works fairly well, but there are a few behaviors that might be show stoppers for us. Any advice would be most welcomed. 1) For a call that TMS recognizes needs to pull in an MCU, can the default Visi...
HiMX300 is not listed in CUCM ver 8.6.2I think device pack required in-order to support this devices.Suppose if i install device pack "cmterm-devicepack8.6.2.23047-1.cop.sgn" or later.It will upgrade all the other phones firmware loads.Problem is, we...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-02-2025 01:27 PM | ||
05-02-2025 12:56 AM | ||
04-30-2025 08:17 AM | ||
04-15-2025 12:31 AM | ||
04-14-2025 12:25 PM |