Hi All, Quick question: I'm currently running UCS v3.2.3 and may need to reconfigure the fiber channel switching mode. According to the UCS doc (https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Network-Mgmt/3-...
Forum Posts
I am planning to add additional ports into the uplink vPC's on the FI's to provide more bandwidth. At the moment there is 2 interfaces in each port channel, on each FI and I'd like to increase that to 4 ports.The environment is all IP storage so I'd ...
Hello, We are preparing a setup for a new VMware environment, on CISCO UCS B200-Series (M4 and M5) and we have VIC 1340 running 1.6.0.37 driver, connected by FI (6248UP and 6332-16UP, running 3.1(3h), soon 3.2(3h)) to MDS SAN to HP 20800R2 storage. ...
Can i Use the Hyperflex without a Hypervisor? can i create VM directly to the Cluster?
Hello, we are using KVM IP Pools in UCS Manager 4. We have one IP for every Blade in the UCS. Is there any way to reduce the number of IPs in the pool and assign them like DHCP with a short lease? thanks, Andreas
Hi everyone, I have one task to mixing 64GB DIMM memory for B200 M4 and B460M4. I try to clarify if we need upgrade memory on B200M4 we need to get this memory from B460 and return to the place if need upgrade B460. I check supported memory types f...
We have 3 standalone C240-M4SX rack servers, running on Windows Server 2016 with Hyper-V installed. I am unable to get SR-IOV working on VIC1227. We have latest firmware installed (from huu 4.0.1b) and latest VIC drivers (4.0.0.3 dated 04.01.2017) SR...
I'be been banging my head on this for a while now. I've attempted all of the other solutions I've found here. Basically, I'm trying to get the server to boot ESXi off of virtual disk 0. This is what I've done so far: Booted into WebGUI for the LSI ...
Hi everone, i am new to hyperflex, i did my first deployment two days ago using the latest HX installer 3.01e and ucs version 3.2.3h and the same for B & C series and vcenter 6.5 U2. i didn't upgrade the ESXI version before cluster creation so it i...
Hi All, Our org is quite new to UCS mini. We are having a weird issue with some of our Esxi servers on B200 M4 blades dropping the Esxi management network for a minute or so periodically daily (Every other network is ok) and I think it may be down ...
I tried searching but I cannot find a clear answer on this. Can the UCS mini be converted from the 6324 IOM's to a 6332 via an online process? or can the config be backed up, the IOM's replaced, and then configs restored to a 6332?
I am looking to upgrade from 6148 to 6332-16UP Fabric Interconnects. I would like some info on steps to do this as I've never installed one. Thanks, Scott.....
Hi We are planning to upgrade UCS firmware from 3.1.3c to latest stable 4.0.1b (starred). We checked the compatibility for Windows 2016 & ESXi 6.7 and found it's compatible. The drivers that we run with the servers are 3.2.1b. Our concern is shall ...
Hello Everyone ! I need some help as i can't access the UCS Manager 3.2(3g) from either of the browsers - IE11, Firefox62X, Edge or chrome - I've modified the JAVA Network Setting to Direct Connection even added the IP of the UCS Manager to the Exce...
Hi,I am trying to install Hyper Flex with 3 nodes and use the nested v Center setup. Initially I used v3.0.1e then I was about to connect to Hyper Flex connect for v Centersetup but it prompt me an error that no cluster was created, so I redo again f...
