Unified Computing System Discussions

Resolved! UCS460 M1 with single drive

Hello,Anybody know if theres any way to make a UC460 to be installed with one hard drive only?. I didn't realized this servers are coming without the RAID card.Best regards.Victor

New VIC 1225

So I see the VIC 1225 is a new card (presumably to replace the P81E), anyone know if it does Adapter-FEX? Only documentation I see is for VM-FEX.

UCS Boot from iSCSI fully supported now?

I'm assuming based on Cisco's documentation that boot from iSCSI on UCS blades is now fully supported (as in TAC will provide support for an problems now)? Correct?Cisco UCS boot from iSCSIhttp://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/...

Resolved! Configuring additonal server ports

Hi, if i'm using 2 server ports per chassis, and wish to add another 2, besides plugging in the cables and settings the ports on the interconnect for "Configure as Server Port" is there anything else that is needed and is there any disruption to traf...

Resolved! UCS C200 M2 - RAID Card R200-PL004 battery back-up

During the installation of a LSI 6G MegaRAID 9260-4i, I'm prompted with the statements "The battery is missing" and "Protect against data loss in the event of a server or power failure by providing emergency power to the cache memory." Can anyone tel...

Resolved! UCS FI6248 In-band management

Hi,We are currently managing our FI6248s CLI and UCS via the out-of-band managment interfaces on the FIs. Does anyone know if the FI6248s can be managed in-band over the 1/10GBe connections?Thanks,

Resolved! Keyboard cannot work after launch KVM in UCS

I am facing strange problem to install ESXi to one of the blade of UCS B200 M2, after replaced both local harddisks, I am trying to install ESXi to this blade again, but after launch the KVM, seems my keyboard cannot communication with KVM, means I w...

HBA Queue Depth

Hi,we use B200 M2 blades with M81KR on 2.02r, running Exchange 2010 on ESXi 5.0 with PowerPath /VE 5.7, the UCS is attached via MDS to a VMAX. EMC Best Practise for EX2k10 is to use PowePath and set the HBA queue depth to 128. How?I picked the "FC Ad...

UCS cannot connect to any FCoe LUNs after reboot

Hi,we have a pretty serious issue we are struggling to get to the bottom of. I have had a Cisco TAC case (and have just opened a netapp case) open now for coming close to a week, and we effectively have a UCS environment that is totally down. Luckily...

VSM location with FlexPod

I've just finished reading the Best Practices in Deploying Cisco Nexus 1000V Series Switches on Cisco UCS B and C Series Cisco UCS Manager Servers document. Near the end there is a section with VSM placement options.None of the options advise placing...

DIMM - correctable-ecc-error

Hi Guys,Just trying to get to the bottom of what this requires to fix.I understand what it''s telling me and I was just going to reset the CIMC but on investigation I am a little confused..It states in the early paragraphs that once the memory is deg...

Is it possible to change the port-channel load balancing policy on the FIs?

We currently have a 2 member port-channel from each of our 6248s up to a 6500, with src-dest IP load-balancing policy set on each side. We're running into an issue where 2 particularly busy servers are getting hashed to a single PC member, and that m...

CIMC Mananger connection

Just configure our c210 box with CIMC Manager. It work for couple of days and the connection just completely went dead on us.We setup with a static IP: 172.16.10.100,with subnet and DG.(we try to change the IP too)We can ping it and log into the CIMC...

Resolved! VIC 1240 - Win2k8R2 Issue

Hi folks,I've got a problem while installing Win2008-R2 over SAN into a LUN with the VIC1240 Adapters on B200 M3 Blades. The Setup ist just not able to find any Remote Storage to install its data. When I use ESXi 5.0u1 everything works fine, the LUN ...

C220M3 Can not find the disk array card ?

Q1 : one processor can not boot ? (Two processors is ok) Q2 : one processor can not detect LSI MegaRAID SAS9266-card? (Two processors is ok) Please help thanks .

Unified Computing System Discussions

Forum Posts

Resolved! UCS460 M1 with single drive

New VIC 1225

UCS Boot from iSCSI fully supported now?

Resolved! Configuring additonal server ports

Resolved! UCS C200 M2 - RAID Card R200-PL004 battery back-up

Resolved! UCS FI6248 In-band management

Resolved! Keyboard cannot work after launch KVM in UCS

HBA Queue Depth

UCS cannot connect to any FCoe LUNs after reboot

VSM location with FlexPod

DIMM - correctable-ecc-error

Is it possible to change the port-channel load balancing policy on the FIs?

CIMC Mananger connection

Resolved! VIC 1240 - Win2k8R2 Issue

C220M3 Can not find the disk array card ?

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

Export from 6248 Fabric Interconnects and import to 6454 FIs

Help, i have a question about Vlans overlapping different vlan groups

B200 M5 Stopped During Boot.

show int Vethernet time interval

Ucsm

Managing vNICs and vHBA's

Compatibility query

UCS Port Channel LACP policy

add a vlan to multiple service-profile remplates vNIC via CLI

CLI command to see IP addresses assigned to the IFM (when using IMM)?