Hello Community Members, Server: Cisco UCS 220 M4SAS Controller: "Cisco 12G SAS Modular Raid Controller"SAS Controller Firmware: 24.12.1-0456Virtual Disk: 1.) RAID-0 with 1 no. of SSD-SAS disk of Capacity 1.8 TB (Linux: /dev/sdb) 2....
Hello Community Members, Server: Cisco UCS 220 M4SAS Controller: "Cisco 12G SAS Modular Raid Controller"SAS Controller Firmware: 24.12.1-0456Virtual Disk: 1.) RAID-0 with 1 no. of SSD-SAS disk of Capacity 1.8 TB (Linux: /dev/sdb) 2....
We have 18 UCS servers with each server having 12 disks each, running hadoop (MapR) on these servers. We are getting disk failures reported by MapR fairly often, say once per month. The problem is UCS manager only seems to report the disk as faulty i...
I'm trying to login to UCS via powershell (using the Cisco powertools module), and so far, i've only been able to login with local credentials. I'm trying to figure out how to login with ldap (AD specifically). Have tried domain\user user@domain d...
We are trying to upgrade firmware of the Intel X710 NIC on our UCS240 M5S servers. The servers are running VMware ESXi 6.7. What is the best and easiest way to update the firmware in this case? I took the usual approach and got the UCS 240 Firmware ...
I am trying to enable alerting on equipment faults or interface down and it appears in 4.X that the Customer ID/Contract...are mandatory fields for enabling Call Home. Any suggestions on how to just get simply alerts? We are looking into intersite i...
Hi I am planning to configure Cisco UCSM Backup . If I select "Policy Backup and Export " and set weekly then its mean it will take Full state and All configuration backups on weekly basis . I have three questions about it . 1) When i configure th...
Hi,Rather than using VMWare Virtual Switch, If I assign virtual NIC from VIC to virtual machine in a vSphere cluster, how vMotion and HA etc work, does the virtual NIC move along with VM? if yes does it require any special configuration?
We've got some newly-purchased B200 M4s with E5-2699 (145W) CPUs. The blades at the end of the chassis (slot 7 and 8) are throwing temperature alerts for CPU2, which is running as hot as 80 deg C on one of the blades. At the same time, CPU1 is only m...
I need help which VMware 6.5 version I can go to with the current CIMC version we have. We just upgraded to 3.0(4r) due to the vulnerability. I really dont want to have to upgrade again but will if needed. UCSC-C240-M4SXIntel(R) Xeon(R) CPU E5-2660 ...
Dear, Please let me know, if the communication between blades in the same or different chassis will happen with Fabric Inter connect itself or the traffic need to switch through the upstream switch.NB: I am using end host mode. regards
Dear , I have the below architecture. as you can see FI_A connected to MDS_A and FI_B connected to MDS_B. both MDS are connected to three storage array (netapp ,hp3par, IBM).My questions :I have only one vSAN (vSAN100) on both MDS (A&B) , the same al...
So iam setting up a C3160 for a client and i have updated all the firmware.Currently i am having trouble finding the CLI command to change the 2nd VIC in SIOC slot 2 to processor node 2.In the update utility i noticed it showed both VIC 1227s connect...
hi,I have 4 UCS C220M3 that needs updates, and I downloaded HUU2.0.3d-1 for this as ISO fileI really want to use a USB drive to boot the UCS of of the box before i shipthem out - So there are no network connectvity - just out of the box, boot to USB ...
Hello Cisco communityWe have configured our ESX cluster and all the vNIC templates per the FlexPod documentation. We are in need right now to segment 3 ESX hosts and create a new cluster (already done)We have to create new VLAN's and assign those new...
Hello, I have a 4 node HX240C-M5SX Cluster.Looking to update firmware per instructions & sequence.Ran HX Health Check 4.1 and ONLY failure is on one HX controller.Indicating: Incidence of OOM in the log file | FAIL | Check for any previous incidence...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-21-2025 07:35 AM | ||
05-20-2025 11:03 AM | ||
05-07-2025 03:02 AM | ||
05-07-2025 12:11 AM | ||
04-30-2025 01:15 AM |