Hi Team,I have a blade B480 M5 with 6146 CPU , I am planning to install redhat 8.9 which is supported starting from 4.2(3) but looks like the CNA Adapter does not support on 4.2(3) for this matrix but 5.0(1) is supporting this 1340. Is there any issu...
Greetings, thanks for reading. I have NetApp storage attached to Nexus 5k for the FCoE zoning and SAN boot and then to ACI.We simply removed those connections to the 5k and instead directly attached to the Fabric Interconnects and went from twinax to...
Howdy Folks, Can anyone confirm if the UCS-FI-6454 can support a copper 10GBASE-T SFP+ module, specifically the SFP-10G-T-X? So far, all I've check the optics compatibility matrix and the 6400 spec-sheet and I see no mention of this module being supp...
If I modify the Firmware Policy with an incorrect version of firmware and it generates pending activities for hosts to get that on next reboot. But I don't want them to get that firmware version. Do I just go into pending activities and cancel them...
Summary:Can ssh into user-2 admin account using password ssh (or via the Web UI)can not use publickey with ssh, always prompts for passwordUser Guide for C-Series doesn't specify any requirements for public key type/bits that i can findI have ssh ena...
Dearsi have a failed HDD for UCS 220M3 servers "Seagate Constellation.2 500GB 7200RPM SATA 6Gbps 64MB Cache 2.5-inch " i have been on the below link for the HDD specs. but now all those listed in the spec sheet are EOS/EOSupport, so i approached in ...
On some of the servers we manage I'm not able to access CIMC. Either IP has changed (I don't have local access) or its not reachable for some reason. However I can access all the servers through vSphere / ESX. Is there any way I can confirm IP Add...
We are attempting to upgrade our current VMWare environment from v6.7 to v7.0U3.We were able to upgrade vCenter with little trouble.However, attempting to upgrade our ESXi host - we only have one on this particular hypervisor - has not been as easy.F...
Hello,We are going to setup X series newly in one of our locations. Just wanted if there are any best practices to be followed and also need to know if this has to be set up in UCSM or IMM Mode as the datasheets for X series 9508 Chassis are having M...
Hi,I am having a weird issue with KVM Launching in a B200 M5 Blade. When I am trying to launch the console without the service profile, I can get to the console normally, whereas when I am launching the console post association of service profile. I ...
Hi All,I am unable to do the cisco hyperflex (Contains 4 nodes) upgrade from and keeps on getting below error. I have already checked firmware/software compatibility before upgrade and also ran pre-check script with no errors/warning in output. ...
Hi everyone,I am having some issues, we have 3 UCS C240 M5 nodes, that have previously been running using the Hyperflex platform and FI.Now we are trying to repurpose them to run another site for us, my superiors made the decision that we will run th...
Anyone knows if is possible and how to do a repurpose of Hyperflex M5 nodes in UCS Managed Mode to use that nodes to install Nutanix cluster with AHV Hypervisor?
Listen here: S11| E2 Cisco Compute Hyperconverged with Nutanix Cisco recently announced a strategic partnership with Nutanix that aims to deliver the industry’s most complete hybrid cloud solution to simplify customer operations, maximize resiliency,...
Hello,I am running cisco UCSM package version 4.2(3d), I joined 2 C240M4L both running 4.4.0.2f for the BIOS and 4.0(2I) for the CIMC firmware trying to upgrade to 4.1(2k). both were discovered successfully, however when I applied the service profile...
