Hi, We have a 3945 with Version 15.5(3)M5 with CUCM 10.5   We have a new ITSP provider that require authentication.   We have configured the authetication in dial-peer level: dial-peer voice 20 voip description ** Outbound SIP-ISP ** .... authentication username <username> password 0 <pass> realm <domain> we have seen that after we send the INVITE, the ITSP answer us with "SIP/2.0 407 Proxy Authentication Required". Unitil here the flow seem ok. The next, the voice-gateway would have send a INVITE with the authentication hearder but instead of the voice-gateway send inmediatly to CUCM "SIP/2.0 503 Service Unavailable" and never send the INVITE to ITSP with the authetication header. apprecite help.   regards ... View more

hi, I am trying convert the mobile (of other area) format in Argentina to e-164 in CUCM (Translation Pattern) and I don't see the way.   Argentina's format for calling to mobile registered in other area:      0<area code>15<mobile number>   Calling from outside of Argentina to mobiles numbers:     +54 9 <area code><mobile number>   my question is try to remove the '15' in the middle of the dialed number. in IOS would be:                 rule 1 /0\(...\)15\(.......\)/ /0\1\2/   For example, a mobile registered in Cordoba (area code 351) and number 1234567:        - From Buenos Aires, dialing 0 351 15 1234567        - From Spain, dialing +54 9 351 1234567   the reason for convert to e164, would be able to overflow from other country if the local circuits are busy or down.   thanks for advance. ... View more

hi, I have tried to understand the licensing of the VVB. Seem that it is related with the CVP VXML Ports.   Currently, we use a CVP with ISR G2 gateway (we bought FL-VXML licenses per gateway ) and we want to move to CVP + VVB (in ESXi). The license are in the ISR and they are not transferable to new environment. I have found that there are a migration license ( CVP-PTS-VVB-MIGRN) with cost 200$ and the maximum quantity is 1. is this license the only product that we need to bought? from ordering guide: 3.3.2.6.1 VVB Migration Licenses Customers who have purchased CVP Port licenses prior to Aug 6, 2016, which did not have the bundled Virtual Voice Browser entitlement, can migrate their CVP Port licenses to include the bundled voice browser licenses. To do this they need to purchase a migration license for each CVP port that needs to be migrated. Each migration license provides entitlement to 1 concurrent voice browser session (VVB or IOS VB) irrespective of the number of voice browser instances deployed in the solution. The migration license details are as mentioned in the table below:   thanks a lot   -- Alberto  ... View more

Hi, is it possible to hide/disable a button (p.e. Direct Transfer) of the call control buttons? Regards, ... View more

Hi, I am installing VVB 11.6(1) on ISR4331 (15.5(3)S4b) and I cannot connect via console. I have followed the guide " Installation and Upgrade Guide for Cisco Virtualized Voice Browser, Release 11.6(1) ". esbarpbxgwt02#show virtual-service list Virtual Service List: Name Status Package Name ------------------------------------------------------------------------------ vvb Activated VVB-11-6-1-ISR4K.ova esbarpbxgwt02#sh ip int brief | i GigabitEthernet0/0/0|Virtual GigabitEthernet0/0/0 10.121.132.11 YES NVRAM up up VirtualPortGroup1 10.121.132.11 YES unset up up interface VirtualPortGroup1 ip unnumbered GigabitEthernet0/0/0 ! interface GigabitEthernet0/0/0 ip address 10.121.132.11 255.255.255.0 negotiation auto ! virtual-service vvb vnic gateway VirtualPortGroup1 guest ip address 10.121.132.67 activate ! ip route 10.121.132.67 255.255.255.255 VirtualPortGroup1 when I try to connect via console: esbarpbxgwt02#virtual-service connect name vvb console Connected to appliance. Exit using ^c^c^c esbarpbxgwt02# I comeback to router a few seconds.   do you find some error? thanks.   SOLVED:::   * I upgraded the IOS and then the vvb responded.            ... View more