Hello,I completely agree that the latest CCA release allows you to do most if not all configuration tasks on a UC500 from the tool. However, there are still a couple of things that you might want to do via the CLI.Is this supported or not? There use...
Hi!We had been running a PAP2-NA unit without problems for quite a while. Last week it started rebooting after every 5-6 seconds and keeps logging the followings:Jan 1 12:00:00 001217FD2269 System started: ip@192.168.6.5, reboot reason:H736c0041Jan ...
Can anyone tell me why the extenion port field would be disable?See the attached image.Restored everything to factory yesterday.I'm 99% sure I was able to assign an FXS port to an extension when changing the role to "User Type" prior to the rebuild.
'm attempting to factory reset a UC560 and running into all kinds of issues...I've tried the below steps on both a Win7 Laptop and WinXP VM (firewall off and other NICs disabled) all running CCA 2.1 (2).From the Maintenance -> Restart/Reset menu, I'...
So I have a two site UC560 setup. Which for the most part was setup using the CCA. Some of the routing/etc had to be done manually due to a MPLS network existing, so there is no VPN its all over MPLS.That said voicemail on site A works fine from ex...
Pardon my ignorance, but Mutliparty conference is enabled. However no of our SPA phones have the conference button whil on an active call. The more softkey does not provide it either. I have looked at the phone templates in CCA and see that our ph...
So the UC-520 blew up on an upgrade and after working with TAC to recover from that, it was just quirky. Decided to just blow it all away and start from scratch. Everything seemed to be working, but my DIDs don't ring their assigned extensions, but...
We have installed a new UC540 with the 8.1.0 service pack. With earlier service packs/firmware, the user was able to input their personal speed dial inside of the web GUI. This doesn't seem possible now. There is also no option to do so inside of ...
Hi all,It's about MWI_Serv and VMWI_Serv parameters.I tried to use these 2 parameters without success: spc error: unrecognized parameter name MWI_Serv[1] spc error: unrecognized parameter name VMWI_Serv[1] I would like to know if with spa303 I can ...
Hi,One of our customers has 4x SPA962 each with 2xSPA932. They randomly restart with various reboot reasons.C4 is one I cannot find in the 'reboot reasons' list (I asked this question there but realize I should have opened a new discussion).Strange...
Hello,We have SPA8800 configured according document: I have 2 questions:1) (problem): Calls from anyone using a SIP Soft phone on a PC can route calls to the PSTN on the FXO ports: Is there a posibility to restrict only to Ip form Asterisk server? I ...
when a call is made from a pstn network to the sip, there is no ringback tone heard. From sip to sip it work good. i included the running config.
This SPA504g phone had power issues when upgrading its firmware. I have tried using spa50x-7-4-4-recovery which gives an error "Recovery Failed: Cannot find the specified device!".The phone and PC are on the same subnet (10.50.60.0/24) and i have tur...
Hi Guys,I am hoping to replace an existing product ime with the SPA2102 phone adapter but I need to know if it is possible for us to make configuration changes etc to these devices via TFTP configuration file uploads as we currently do with our Grand...
Hi,Need help provisioning SPA303.FW: 7.4.7Model: Cisco SPA303 Have set up the profile rule: http://company.com//linksys/$PN/spa$MA.cfg, however upon boot up, device does not even request or point to that url instead it requests for:Read Request, File...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: