I have PIX515 with Version7.0. Andfew of clinents usingCisco VPN client 5.0.0..36 to connect to office. Now i have a windows 7 64bit laptop.Whihc version of vpn softare i can use and how.Pls help
I have a quick quesiton here in genernal when you set up an encryption domain for an ipsec tunnel the subnet maskof your encryption domain must match your source/destination subnet mask. So for example say you have a sourceof 170.132.128.0/24 and d...
I have been unable to make SUA work with easy VPN. I have an asa 5505 (client) and an asa 5520 (Server).When the config is like this:5505:vpnclient server 192.168.1.0vpnclient mode network-extension-modevpnclient nem-st-autoconnectvpnclient vpngroup ...
Hi AllIm new to ASAs, I managed to setup a little ASA 5505 for remote vpn using the nice little built in vlans 1 and 2I have started to configure an ASA 5540 (IOS 7.2 ASDM 5.2) for remote vpn and have come across a problem, VPN connects fine but the ...
Hi all!I need to configure Remote Access VPN on a router 1751. But this router receives dynamic IP (PPPOE - DSL) of the provider. I know to configure static IP, but do not know for PPPOE dynamic IP.Attach topology and configuration for Static IP (wor...
hi,I have setup an easyvpn between a ASA5510 and a 877 router. Each time the tunnel goes down, i am prompted to enter my username and password See below.Sending XAuth Request, Please enter the following command:*Mar 3 18:51:32.919: EZVPN: crypto ips...
Hi, I have had the VPN-client, version 4.8.00.0440 installed for years.I have just uninstalled this version, tried to install the 5.0.01.0600 that came along with our ASA 5500. It froze just before finishing up.I have then downloaded the latest versi...
I am trying to configure a Cisco 871W router to terminate connections from a Cisco VPN client.I can successfully connect to the VPN Router using the Cisco VPN client version 4.8.02.10.However ....I can't access ANY resources on the network.I tried pi...
Hello there!I´ve been trying to configure a VPN Tunnel between Check Point NGX R65 and ASA5510-CSC10-k8, but I suppose that I get a problem. The ASA5510-CSC10-k8 use the Data Encryption Standard (DES) license and it seems tha the Check Point don´t ac...
Hello everyone,I have a problem with a gre tunel. When the router is reload the interfaces tunel go down and go up when I reconfigured the tunnels.The router is a 2821 and the version is:c2800nm-adventerprisek9-mz.124-15.XZ1.binThanks in advanced!
I am going to use an ASA-5540 as our VPN head-end termination device only - and not as a firewall.Also, we have a routeable class-B address for our internal enterprise address space, so we have no need to NAT. I'd like to turn off the NAT 0 function ...
Hi experts,Attached to this mensage I put a image .jpg with my topology. Is it possible configure the ASA to user SSL VPN to authenticate in the radius through the L2L VPN?In ASA console a I do not can ping the radius IP address 10.0.79.15. There are...
Hi,I'm about to drop kick this ASA 5505. Basically what happens is upon install the 5505 connects to the 5520, establishes the tunnel and all is well. Within 10 or 15 minutes, everything drops, and the VPN tunnel refuses to come back up until I reloa...
We have a handful of PIXes and ASAs running at remote locations configured for EZVPN. What we want to do is to force all traffic from the remote locations through a content filter, which doesn't act as a proxy. Given that the gateway for the VPN conc...
Using an ASA-5505, I only have private IPs on the local LAN and one public IP address from my ISP for the peer address. Can I use that same peer IP address as a PAT or NAT for my internal local private IPs? The remote VPN location policy is to not a...
